The One-Answer Question Thread [closed]

Status
Not open for further replies.
skeletonboy said:
Yes they are the same, intuitive F2L.
Click to expand...

even tho they use different algs and stuff?
like for example the first one involves first putting the corner into its correct position (not necessarily correct orientation)
but the second involves putting the corner above its correct position...
still same thing?
is one faster than the other?

And another unrelated question:
what would be the cheapest place to buy a wittwo stickerless
thanks
 
Last edited:
cubingawsumness said:
even tho they use different algs and stuff?
like for example the first one involves first putting the corner into its correct position (not necessarily correct orientation)
but the second involves putting the corner above its correct position...
still same thing?
is one faster than the other?

And another unrelated question:
what would be the cheapest place to buy a wittwo stickerless
thanks
Click to expand...

They are slightly different in teaching. Someone could say: If you get xxxx case, then perform the algorithm xxxxx.
Other people might say: First you do this xxxxx, then you do this xxxxx, then you pair it up like xxxxx then you use the algorithms xxxxx and then insert xxxxx.

Really, just different ways, intuitive F2L has variables, that's why it's called intuitive. You could do : put the corner on top of the slot and do xxxxx
Or you could do: put the corner on the top right slot and perform xxxxx.

So, people can talk like they're teaching you intuitively, but after they "talk" about the case, they just give you an algorithm.

Some people simply give you an algorithm. S

ome people can talk and talk and describe the whole video through without using case algorithms. And example of doing this is Badmephisto's video, although he might give you short insert algorithms, he speaks and teaches and performs very intuitively.

I say you just learn both of them, so you kinda get the best of both worlds. None is faster, just depends on what case you get.
 
cubingawsumness said:
oooh that looks cool
maybe ill watch it later (probably tomorrow cuz its kinda late)

skeletonboy:
alright i guess that makes sense: people have different ways to do it and different ways to teach it
ill take a look at badmephisto's video to see if its very different than these 2
Click to expand...

RiDo's Hunting Story Method is a very good way to enhance your knowledge in F2L if you're having a bad time learning F2L. It's quite fun to learn it, very clear and logical.
 
KJ said:
Hi, I have a question.
I wanna post a video to Bapao's cube giveaway, but when I try to select it in to attach, the video is grayed out.(NOTE: I do not have afacebook or youtube, because I am 10 years old, and I am using a video that I made using a mac camera)
Any suggestions on how I can post the Vid?
Click to expand...

Check out THIS site. You can upload videos and pics there and link to the files from a forum, etc. Your age will not be an issue, as you don't have to register an account to use the service. I'm not sure that you will be able to embed the video here, but you will at least be able to provide a link to it.
 
hey, i tensioned my zhanchi a little wrong and now it wont corner cut 45 degrees. do i loose or tight the screw?

btw.. what order should i tension the cube? white first or what?
 
Last edited by a moderator:
Loosening the screws will make it cut more. What I do is take all the cubies out and pull the center pieces away from the core and check to see how far them move... (I tend to go for about 2mm) and I check all the different sides to make sure they are about the same (having one side that is much looser than the others will mess up the tension).
 
Lanttikasa said:
btw.. what order should i tension the cube? white first or what?
Click to expand...
1. There's no need to double-post..please just edit your previous one instead.
2. It doesn't matter what order you tension it in. Just make sure all the sides are adjusted to the same tension. As for exactly how tight this is, it's something you'll have to play around with and figure out for yourself as it mostly comes down to personal preference.
 
peterbone said:
Why would it matter what order you tension the cube? You just have to make the tensions equal. If it's not cutting well then you'll need to loosen it.
Click to expand...

ok now i tried to loosen it but it still does not corner cut.. then also tried to retension over and over again and the red side is always too slow.. guys help me..
 
I recently took up speedcubing, and I really want to begin competing. My best AVG5 is 30.53 and my PB is 24.56. Would I embarrass myself? Also, Are there any competitions in the vicinity of NYC? I do not want to travel very far.
 
Foster Conklin said:
I recently took up speedcubing, and I really want to begin competing. My best AVG5 is 30.53 and my PB is 24.56. Would I embarrass myself? Also, Are there any competitions in the vicinity of NYC? I do not want to travel very far.
Click to expand...

Of course you wouldn't embarrass yourself. The speedcubing community is one of the nicest out there. Competitions are a great way to have fun and meet other cubers. Go for it when you can. :D
 
HELLO!!! Yesterday, while I wasn't looking, somebody switched two of the stickers on my rubiks brand 3x3. I already have a zhanchi but I like being able to have a cube that I can take with me everywhere without worrying about getting it dirty or broken. So the million dollar question: After I switched the two stickers back, they won't stay on the cube very well. How can increase the life of those peeled stickers?
 
Status
Not open for further replies.

Similar threads

T
One answer random question thread
Replies
8
Views
1,771
tnk351
T
AlexvanVugt
One-Answer Square-1 Question Thread
5 6 7
Replies
138
Views
25,071
Renslay
Renslay
shadowslice e
One-Answer Puzzle Theory Question Thread
8 9 10
Replies
193
Views
33,016
eeeeeeeee
eeeeeeeee
B
  • Locked
One-Answer 3x3 Roux Question Thread
7 8 9
Replies
164
Views
32,645
PiKeeper
PiKeeper
Note
One-Answer 2x2x2 Question Thread
14 15 16
Replies
317
Views
46,258
Renslay
Renslay
Back
Top