The One-Answer Question Thread [closed]

[Rpotts]

M2' U' M U2' M' U' M2'

Do all M2s using ring-middle double triggers. I do the M pushing up on DB with my middle finger.

 

[Cool Frog]

What are your opinions of this PLL
R U R2' U' R' F R U R U' R' F' R U R U' R'
Besides the high move count i find it finger tricky

 

[Rpotts]

most fast people can do the 9 move commutator A perm sub-1. I doubt many could sub-1 that alg. If you don't like the normal alg have you tried -

R U R' F' r U R' U' r' F R2 U' R'

It's the common J perm with two r turns instead of the normal R turns.

 

[JonnyWhoopes]

What is an algorithm for pure double parity on a 4x4x4?

 

[~Phoenix Death~]

What is an algorithm for pure double parity on a 4x4x4?

r2 B2 r' U2 r' U2 B2 r' B2 r B2 r' B2 r2 B2

 

[ravenguild08]

I was about to buy some CRC Heavy Duty silicone spray (red can) when I saw a huge warning on it advising against use on plastic. Does everyone else's say this as well? I don't want to spend $5 to melt my cube... Thanks.

 

[EricReese]

I want to lightly sand my guhong. Do I sand the corners + the edges? I assume the pieces will need to be cleaned after i sand them correct? Do I just take a semi wet paper towel and wipe them off? Thank you

 

[~Adam~]

If you really want to sand it only slightly use extremely high grit wet and dry sandpaper.
(I assume you are trying to quickly get rid of the slightly rough feel some have to begin with)

 

[stinkocheeze]

best glow in the dark cube from lightake?

 

[EricReese]

If you really want to sand it only slightly use extremely high grit wet and dry sandpaper.
(I assume you are trying to quickly get rid of the slightly rough feel some have to begin with)

Yes that is it. Do I sand the edges + corners all around slightly? Perhaps I should try to find a video on youtube.

 

[d521yts]

How can i do d and u moves easier?

 

[vcuber13]

What is an algorithm for pure double parity on a 4x4x4?

how do you have a "pure" 4 cycle? whats unpure?

How can i do d and u moves easier?

x2 U D

 

[TheMachanga]

Forgive me if this is a stupid question, but who assembles factory cubes? I'm assuming the producer hires people to assemble them. I can just imagine a row of workers assembling throughout the day. They can probable assemble a v-cube mech 4x4 in less than 3 minutes. Amirite?

 

[Rpotts]

I was about to buy some CRC Heavy Duty silicone spray (red can) when I saw a huge warning on it advising against use on plastic. Does everyone else's say this as well? I don't want to spend $5 to melt my cube... Thanks.

1. Buy it.
2. Use it.
3. Love it.
4. Observe your cube not melting.
5. ??????
6. PROFIT

 

[da25centz]

I was about to buy some CRC Heavy Duty silicone spray (red can) when I saw a huge warning on it advising against use on plastic. Does everyone else's say this as well? I don't want to spend $5 to melt my cube... Thanks.

yeah its fine

 

[stinkocheeze]

What is a good glow-in-the-dark cube on lightake?

 

[vcuber13]

Forgive me if this is a stupid question, but who assembles factory cubes? I'm assuming the producer hires people to assemble them. I can just imagine a row of workers assembling throughout the day. They can probable assemble a v-cube mech 4x4 in less than 3 minutes. Amirite?

i would infer machines do that

 

[TheMachanga]

Can someone link me a good 3op corner set-up moves guide?

 

[xbrandationx]

How much does a can of CRC cost at Walmart/Target etc?

 

[Rpotts]

< 5 $