The One-Answer Question Thread [closed]

Status
Not open for further replies.
NooberCuber said:
I was thinking of taking apart and lubing my moyu aosu today and was wondering where i should apply lube
Click to expand...

I wouldn't take it apart completely.

It's the worst cube ever to put back together, especially lubed. :/ You would be better off taking out an edge and just putting in some Maru or something. I'm no expert obviously, but that was my experience. It took me at least 2 hours to get it back together.
 
I am currently learning full Oll, I know about 35 cases. I want to ask that should I learn the dot cases? I can use a sledgehammer while inserting last pair if no edges are oriented so I don't think I will ever get a dot case. Also if I learn all olls except dot cases, will that be considered full Oll?
 
the super cuber said:
I am currently learning full Oll, I know about 35 cases. I want to ask that should I learn the dot cases? I can use a sledgehammer while inserting last pair if no edges are oriented so I don't think I will ever get a dot case. Also if I learn all olls except dot cases, will that be considered full Oll?
Click to expand...
No, that would not be full OLL. Unless you never use the separated pair insert you will have to build the pair then sledge which wastes a lot of moves, so I would and did, it's not a lot of algorithms.

Edit:
Are the last four center and corners algorithms available anywhere for ranzha skewb method?
 
Last edited:
I just got into 4 x 4, and my Moyu Aosu literally has 0 reverse corner cutting. Its regular corner cutting isn't too amazing either, but the problem with the reverse corner cutting is that since it's so poor, a lot of my algs that go …U' R' get locked up as a result. Is there any way to fix this, or this a common 4 x 4 problem ?
 
ajayd said:
I just got into 4 x 4, and my Moyu Aosu literally has 0 reverse corner cutting. Its regular corner cutting isn't too amazing either, but the problem with the reverse corner cutting is that since it's so poor, a lot of my algs that go …U' R' get locked up as a result. Is there any way to fix this, or this a common 4 x 4 problem ?
Click to expand...

Your cube is probably just tight, though it is true that 4x4 corner cutting isn't going to be as good as 3x3 of course.
 
My Shuangren Illusion is locky, rough, catchy and does not corner cut very well. How do I fix this? How do i fix the tensions, the center caps seem to be stuck to the core and i dont want to destroy the cube.
 
DoctorPepper said:
My Shuangren Illusion is locky, rough, catchy and does not corner cut very well. How do I fix this? How do i fix the tensions, the center caps seem to be stuck to the core and i dont want to destroy the cube.
Click to expand...
If it feels too tight then yes, you will probably have to tension it to get it to your liking. It can be a bit tricky at first to tension and lube a 54.6 FangShi if it's assembled but it's not impossible. All you have to do is push the center cap out through one or two of the holes in the center piece using something sharp like a paperclip or pen tip.
 
Status
Not open for further replies.

Similar threads

T
One answer random question thread
Replies
8
Views
1,769
tnk351
T
AlexvanVugt
One-Answer Square-1 Question Thread
5 6 7
Replies
138
Views
25,032
Renslay
Renslay
shadowslice e
One-Answer Puzzle Theory Question Thread
8 9 10
Replies
193
Views
32,944
eeeeeeeee
eeeeeeeee
B
  • Locked
One-Answer 3x3 Roux Question Thread
7 8 9
Replies
164
Views
32,575
PiKeeper
PiKeeper
Note
One-Answer 2x2x2 Question Thread
14 15 16
Replies
317
Views
46,092
Renslay
Renslay
Back
Top