The One-Answer Question Thread [closed]

[devoblue]

I have all three, un-modded
IMO A5 > Haiyan > AVf

 

[Ordos_Koala]

Out of all the current Alpha cubes(AV, Haiyans, or V-F). Which one is the best? I getting one of these because I am completely dissatisfied with my GuHung.

I don't see how anyone can be dissapointed with GuHong, but it may be really on preferences... you could try something with that crispy feeling like AV has (if you wouldn't be satisfaied, you can mod it into hayan memory)

So I'm at stage where I am getting constant sub 22s,my NL pb is 17.xx and Lucky pb is 16.41

I reached here because i went slow on F2L and improved my lookahead quite a lot in the past 2 weeks,I was averaging 30 before that.

Umm so what next should I do to be sub 15,I don't think more slow turning for F2L will help anymore,

Basically my question is now,at this stage...If i want to get more faster,should I force myself to turn and insert F2L pairs like a maniac?

you could learn some advanced technices as x-cross... for practice I think just consistent solves can do the job

 

[TheMachanga]

Is there any other way to load money onto your paypal account without using Greendot Moneypak? Literally almost every link on google leads me to horror stories about them scamming you and losing money, and how it doesn't work.

 

[sa11297]

which yj 5x5 is better? 1st gen, 2nd gen, or upgrade edition?

http://www.lightake.com/Search.do/Search.yj 5x5x5

 

[cuberkid10]

1st gen is a KO eastsheen 5x5. 2nd gen and upgrade edition are like V-cubes with screws and springs.

 

[Julian]

Just got my mf8 + dayan 4x4. What should I do to make it good?
Right now, out of the box, it's popping one edge a lot.
Thanks.

 

[Lorken]

I haven't touched my cube in a long time now, but I came on today just to see what's up, and I kept seeing the Elite cube, what is it?

 

[danthecuber]

I haven't touched my cube in a long time now, but I came on today just to see what's up, and I kept seeing the Elite cube, what is it?

This post describes that ELITE very thoroughly

 

[HavoCentral]

At what point during a comp do I hand over my cube?

I have a special process I do to my cube before I do avgs, but it works best for about 30 min afters I do go through the process.

 

[RCTACameron]

They will call out something like "could the people doing 3x3 please put their cubes here", which is when you put your cube on the scrambling table. Then you just wait until you get called (the amount of time for this to happen can vary a lot.)

 

[HavoCentral]

that sucks, cuz my thing I do, makes my cube wayyyy better for about 30 minutes.


Also are there any FII mods to reduce lockups? Like rounding the edge and corner stalks.

 

[EricReese]

What is the best pure flip 4x4 OLL parity alg? Apparently you can do a variation of the standard "r2 B2" one without wide turns or somethinng?

 

[HavoCentral]

What is the best pure flip 4x4 OLL parity alg? Apparently you can do a variation of the standard "r2 B2" one without wide turns or somethinng?

http://www.youtube.com/watch?v=Cfjq6Tap8zE

Enjoy, and have fun.

alg is in the comments

 

[tx789]

Has any ideas how to meld two piece together my QJ megaminx dark purple center snapped off and I want to repair it rather than buying a new one.

 

[HavoCentral]

Has any ideas how to meld two piece together my QJ megaminx dark purple center snapped off and I want to repair it rather than buying a new one.

Where did the break occur?

 

[Lorken]

that sucks, cuz my thing I do, makes my cube wayyyy better for about 30 minutes.


Also are there any FII mods to reduce lockups? Like rounding the edge and corner stalks.

Wait, are you joking about what you do with your cube? It sounds pretty redic.

Also, I would say if there was anything, it would be sanding the inside edges of the corner pieces.

 

[Krible]

I know 2look oll and im ready to learn full oll. Can anyone recommend a video tutorial showing all the olls? Preferably fast and fingertricky.

 

[TheMachanga]

I know 2look oll and im ready to learn full oll. Can anyone recommend a video tutorial showing all the olls? Preferably fast and fingertricky.

It's better to learn them off a website with diagrams. You can print them out too.

 

[danthecuber]

It's better to learn them off a website with diagrams. You can print them out too.

Use these sheets. I've search around everywhere for printable sheets, but I have not found anything better.

 

[Julian]

Just got my mf8 + dayan 4x4. What should I do to make it good?
Right now, out of the box, it's popping one edge a lot.
Thanks.

Bump.