The Truth About Corner Cutting

[DavidWoner]

Let everyone see for themselves how well their favourite cube really cuts corners.

My favorite cube wasn't in your video.

If your favourite cube wasn't in there, then it probably sucks.

Or maybe it wasn't in there because it's sitting on my desk instead of being in new zealand.

 

[Metroidam11]

This video moves around too much and gives me a head ache. Also this does not disprove anything I already know about corner cutting.

 

[Whyusosrs?]

k, your guhong is set way too tight. Mine can cut more then your A2 SV. Also, your reverse corner cutting is lulz.

 

[buelercuber]

why is your GuHong so ****ing tight?

mine can cut 47. easily

 

[Whyusosrs?]

you measured? wow. neeb.

 

[hawkmp4]

Yeah, seriously...I've seen claims of 43 degrees and 47 degrees in this thread. Where are you getting those numbers? Breaking out a protractor?

 

[buelercuber]

It cuts at a 45 degree angle, which is line to line.

Wrong. Idiot.

lol its when the edge of a corner aligns with the center of a center piece.
right? lol

 

[~Phoenix Death~]

A lot of you need to take a look at Stefan's page at corner cutting, cause he actually knows what he's talking about. http://www.speedsolving.com/forum/showthread.php?t=18871

 

[hawkmp4]

It cuts at a 45 degree angle, which is line to line.

Wrong. Idiot.

lol its when the edge of a corner aligns with the center of a center piece.
right? lol

Do you really not understand what a 45 degree turn is, or are you trolling? I can't tell...

 

[~Phoenix Death~]

My F-II can cut corners at 36.87 degrees.

 

[StachuK1992]

It cuts at a 45 degree angle, which is line to line.

Wrong. Idiot.

lol its when the edge of a corner aligns with the center of a center piece.
right? lol

This shows a 45 degree angle.

So does this:

 

[Stefan]

lol its when the edge of a corner aligns with the center of a center piece.
right? lol

Do you really not understand what a 45 degree turn is, or are you trolling? I can't tell...

Wait, now I'm confused. Do you think his description is wrong?

 

[hawkmp4]

lol its when the edge of a corner aligns with the center of a center piece.
right? lol

Do you really not understand what a 45 degree turn is, or are you trolling? I can't tell...

Wait, now I'm confused. Do you think his description is wrong?

His description is clearly correct. What threw me off was that he asked, "right?" as if he wasn't sure.

 

[~Phoenix Death~]

It cuts at a 45 degree angle, which is line to line.

Wrong. Idiot.

lol its when the edge of a corner aligns with the center of a center piece.
right? lol

This shows a 45 degree angle.

So does this:

So is this

 

[Olji]

It cuts at a 45 degree angle, which is line to line.

Wrong. Idiot.

lol its when the edge of a corner aligns with the center of a center piece.
right? lol

This shows a 45 degree angle.

So does this:

So is this

so is this

 

[Chapuunka]

Whoa, picture overload. Spoilers plz.

So Dene's serious here? I thought this was just super good trolling.

 

[Dene]

I was being serious. The point was not that the cubes can't cut corners well. I'm just sick of comments like "my guhng cn cUt cornres at 45 dgreeez even wen its tIght!!!!1111!!L OLMAOF2L !!1!!" It isn't true. My cubes aren't even that tight, as I clearly demonstrated with the Guhong. But you can see for yourself it doesn't cut corners very well at all.

All of them are lubed except the black A5, which I forgot to say (in this take) is not lubed. And for your information, I use exactly the same lube that Faz uses so don't go calling my lube crap.

I'll quickly respond to a few comments:
I have already been informed of my "reverse corner cutting" mistake. For some reason I was under the wrong impression of what that was, but I don't think I need to bother making a new video showing the actual reverse corner cutting abilities of these cubes.
fatboyxpc: I don't get your point? I'm not sure why you would think I'm a "strickler". This was not a review, this was me providing hard evidence of something which I believe people are under the wrong impression about.
Woner: indeed
Blah: really?

 

[Kirjava]

What you refer to as a small amount of corner cutting is more than enough for anybody.

 

[maggot]

your A2 is pretty impressive i must say. . . so is lacey from flyleaf **drool**

 

[ChrisBird]

People care too much about corner cutting.

This.

Yeah, seriously...I've seen claims of 43 degrees and 47 degrees in this thread. Where are you getting those numbers? Breaking out a protractor?

Out of their ass probably.

What you refer to as a small amount of corner cutting is more than enough for anybody.

This.

~Chris