One Answer Question Hardware Thread

I keep locking up on my Weilong v2. I don't have problems with overshooting, it just doesn't gets caught, especially when I'm trying to do G-perms and stuff really quickly the layers misalign and stuff. I haven't lubed or tensioned it since I got it ~3 weeks ago. How can I stop locking up?
 
lerenard said:
I keep locking up on my Weilong v2. I don't have problems with overshooting, it just doesn't gets caught, especially when I'm trying to do G-perms and stuff really quickly the layers misalign and stuff. I haven't lubed or tensioned it since I got it ~3 weeks ago. How can I stop locking up?
Click to expand...

Then tension it!
 
I have a Calvin's Square 1 and some of the caps on the pieces fall off constantly. Would super gluing the caps be recommended?
 
Where can I get a Black 57mm Aolong V1 still? It's discontinued, so I can't find anywhere except lubix but they charge like $8 for shipping.
 
lerenard said:
Should I tighten it or loosen it? Sorry I'm a noob. Everytime I try to change something about my cubes, they get worse D:
Click to expand...

Maybe try loosening it up so it doesn't lock up as much. If it's too loose, just tighten it up a little until you get it to a preferable tension. Also try to make sure each side is tensioned equally.. I believe JRCuber has a video about tensioning that might be useful.. :)

avantagomese said:
Where can I get a Black 57mm Aolong V1 still? It's discontinued, so I can't find anywhere except lubix but they charge like $8 for shipping.
Click to expand...

Hmm.. Can't see it anywhere.. Maybe on Amazon or something but not at any cubing stores.. If I do find a store that has a Black 57mm Aolong V1, I'll edit this post (Or someone else can beat me to it. ._.)
 
Note said:
I have a Calvin's Square 1 and some of the caps on the pieces fall off constantly. Would super gluing the caps be recommended?
Click to expand...
You could but I wouldn't, I was told at a competition that the only use for cigarette papers is wedging them between the caps of square-1s. So stick some thin paper or cigarette paper if you happen to have some just to make the gap tighter. Don't smoke, kids!
 
How do people get their Dayan 2x2s so fast? Mine is sort of smooth but there is a lot of static friction (force needed to start a turn?) I've tried a Dayan 2x2 that is sooo sooooo fast and I don't know what I'm doing wrong. I've tried Maru, weight 2, and nothing works.
 
guysensei1 said:
How do people get their Dayan 2x2s so fast? Mine is sort of smooth but there is a lot of static friction (force needed to start a turn?) I've tried a Dayan 2x2 that is sooo sooooo fast and I don't know what I'm doing wrong. I've tried Maru, weight 2, and nothing works.
Click to expand...
I would like to know this as well. My Dayan 2x2 is horrible, but everyone else's that I have tried it amazing.
 
guysensei1 said:
How do people get their Dayan 2x2s so fast? Mine is sort of smooth but there is a lot of static friction (force needed to start a turn?) I've tried a Dayan 2x2 that is sooo sooooo fast and I don't know what I'm doing wrong. I've tried Maru, weight 2, and nothing works.
Click to expand...

Same here. If I loosen it, it will just pop all the time. It's gotten better since I first got it, but there's too much static friction (hard to start turning, and jerks when turned slowly too).
 
(Is this question in the right place?)

Would it be best to use cubes that fit how good you are at cubing? Like using a slower cube if another feels too fast for you? I have a Gans3 V3 but it kinda feels a bit flimsy.. Will I get used to it over a couple solves or should I just switch back to my Guanlong then use the Gans3 when I get faster? ..I'm sub-30 by the way..
 
Last edited:
Note said:
(Is this question in the right place?)

Would it be best to use cubes that fit how good you are at cubing? Like using a slower cube if another feels too fast for you? I have a Gans3 V3 but it kinda feels a bit flimsy.. Will I get used to it over a couple solves or should I just switch back to my Guanlong then use the Gans3 when I get faster? ..I'm sub-30 by the way..
Click to expand...

I don't think that your average should decide which cube you choose, as long as it is a speedcube. You should be choosing a cube that feels comfortable in hand and feels well to you. For example, although my Aolong v1 is slightly faster than my Aolong v2, I can't get it to work well as it feels too flimsy, and I'd get corner twists every ten or so solves. Just choose the cube you like, so if you can't get used to the Gans v3, switch back to your Guanlong.
 
i got a guanlong and want to put washers in them. Which type of hardware is compatible with these. I know its a 56mm puzzle so its strange.
Thanks
 
You must log in or register to reply here.

Similar threads

D
The one-answer question thread (for Hardware & Buy, Sell, and Trade)
2 3
Replies
44
Views
6,977
Godmil
Godmil
*LukeMayn*
  • Locked
The One-Answer Question Thread [closed]
1835 1836 1837
Replies
36,733
Views
4M
Sa967St
Sa967St
T
One answer random question thread
Replies
8
Views
1,769
tnk351
T
AlexvanVugt
One-Answer Square-1 Question Thread
5 6 7
Replies
138
Views
25,032
Renslay
Renslay
shadowslice e
One-Answer Puzzle Theory Question Thread
8 9 10
Replies
193
Views
32,944
eeeeeeeee
eeeeeeeee
Back
Top