ShengShou 7x7 vs. V-Cube 7

Which 7x7 Do You Prefer?

  • ShengShou 7x7

    Votes: 165 85.1%
  • V-Cube 7

    Votes: 27 13.9%
  • Other

    Votes: 2 1.0%

  • Total voters
    194
I got a Shengshou a few weeks ago and really didn't like it out of the box. I'm planning to mod it and such, but I haven't had time yet. So for now I'm sticking with V7, but I think I'll like the Shengshou better once I've done a few basic mods.

I had absolutely no need for any mods to my SS7. I think it just may feel awkward because of the new shape and larger size. Your hands take quite a while to get used to it, and I still get tired after doing some practice.
 
I prefer the SS 7x7 over the V cube simply because it doesn't pop. My V cube pops normally around 5 times a solve so it's nice to have a cube that doesn't do that.
 
You should consider buying a Type C WitTwo.. it is without a doubt the best 2x2x2 speedcube out there. It has a nice scratchy feel to it and to lubricant it reacts very well.
 
After using the V7 for a while, the Shengshou doesn't seem square; it's like it seems hollow.

Anyway, I modified a Shengshou 7x7x7 following the usual mod for 5x5x5s and now it reverse corner cuts. But it also makes more racket and is more likely to pop:
ss7x7.jpg
 
Maybe I just got a good one, but my ShengShou 7 is THE best big cube out there IMO.
By "big cube" i mean anything over 4X4.. I own or have owned almost every big cube.
I think it's also worth mentioning that I haven't done a single mod to it either.
 
Come to think of it, I don't recall ever popping it either which is pretty remarkable for a big cube. I managed to order my SS7 the first day they were available and I've been using it daily since.
 
After using the V7 for a while, the Shengshou doesn't seem square; it's like it seems hollow.

Anyway, I modified a Shengshou 7x7x7 following the usual mod for 5x5x5s and now it reverse corner cuts. But it also makes more racket and is more likely to pop:
View attachment 2214

That's overkill o_o what tools did you use and how long did it take you?
 
That's overkill o_o what tools did you use and how long did it take you?

After experimenting with various things, I think that the best way of removing plastic is a flat 2nd cut file. It leaves a smooth surface. The tool is cheap and never wears out. It cuts quickly and is very controllable.

The modification means beveling 480 edges. (There are 20 edge holes per side so 20x6 = 120 holes to expand. At each hole, four cubies meet, so 4x120 = 480 bevels.) If you can do one in 15 seconds, which is reasonable, the whole thing will take about 2 hours. I took longer because I beveled more than just the outer-most edge.

But I didn't expand the inner holes because my experience is that they don't lock up much. The worst locking problems are when you're in the final stage. So I did those holes only. Unfortunately, that's the majority of the holes; there's only 6x6 = 36 on a side total.

I'm going to do the same thing to one or both of my other SS 7x7x7s as it means I don't have to line it up as carefully when I turn it. And I'm not sure it makes it pop more because one of my unmodified SS 7x7x7s just popped the same way. This time I'll remove a little less plastic. And I'll probably bevel only the outer-most edges as those seem to be where things get locked.
 
After experimenting with various things, I think that the best way of removing plastic is a flat 2nd cut file. It leaves a smooth surface. The tool is cheap and never wears out. It cuts quickly and is very controllable.

The modification means beveling 480 edges. (There are 20 edge holes per side so 20x6 = 120 holes to expand. At each hole, four cubies meet, so 4x120 = 480 bevels.) If you can do one in 15 seconds, which is reasonable, the whole thing will take about 2 hours. I took longer because I beveled more than just the outer-most edge.

But I didn't expand the inner holes because my experience is that they don't lock up much. The worst locking problems are when you're in the final stage. So I did those holes only. Unfortunately, that's the majority of the holes; there's only 6x6 = 36 on a side total.

I'm going to do the same thing to one or both of my other SS 7x7x7s as it means I don't have to line it up as carefully when I turn it. And I'm not sure it makes it pop more because one of my unmodified SS 7x7x7s just popped the same way. This time I'll remove a little less plastic. And I'll probably bevel only the outer-most edges as those seem to be where things get locked.

So from your experience the puzzle locks the most during the 3x3 phase? Yes, I prefer files and sandpapers while modding too :)
 
I vote Shengshou. My v-cube takes so much more effort to turn compared to a Shengshou. My hands generally hurt after a v7 solve, but feel fine after an ss7 solve. I also dropped my PB from 8:22 with a v7, to a 7:09 with the ss in ONE solve.
 
I also vote Shengshou because for some reason my times went down a lot since I started using it.
However, my v-cube turns as well as the Shengshou and has better corner cutting. On the other hand, the v-cube pops and several pieces broke already so I had to replace those.
 
Back
Top