Problem With F-II Caps

I couldn't be bothered glueing so I just cut some paper and put it between the cap and where it goes into the cube, to tighten it. It's working fine so far.

You couldn't be bothered to use a little glue, but you could be bothered to get out paper, cut it into the exact size pieces, and then go to the effort of getting it in under the caps without any paper showing?

I think glue would be much easier.

(btw I used glue).

Well I didn't have glue at hand (I never glue anything) so paper was easiest. It's not as bothersome as you make it out to be, I just one long strip of about the right width and cut a some of it off when I needed it. The ridge on the caps help push the paper in without it poking out.
 
When I restickered my FII I took the old stickers and stuck them over the ridges on the cap which jams it in quite nicely. Also when restickering it becomes apparent which caps need to be jammed in as they will pop off while peeling off the sticker so yea.
 
I used Elmer glue for mine, it holds but it's easy to get out if you need to do something in there (don't know why you would want to, but it's easier than using super glue in my opinion, that stuff is too messy).
 
I glued them on using the video two posts above me but guess wat happened now. I was running at school. I fell and I had my cube in my pocket. A core piece snaped off. The spring and screw are intact but the pastic broke. Is there anyway I can fix it.
 
I glued them on using the video two posts above me but guess wat happened now. I was running at school. I fell and I had my cube in my pocket. A core piece snaped off. The spring and screw are intact but the pastic broke. Is there anyway I can fix it.

OPTIONS:
Superglue it (temporary fix, be very careful)
Get a new core
Get a new cube
Don't run in the hallways
 
My core broke too. Was yours the blue core or the gray core? Gray ones are much stronger. If you need a new core, I highly recommend using D-II core + hardware. Under no circumstances use type A core + hardware (at least the old ones) as it will suck for ever and ever and ever until you switch them out.

If you are going to superglue it, don't over-do it, or it wont stay.
 
I have a gray core. But my hole body weight was on it so.... Anyway what do you recommend I do. Keep in mind my parents don't know I broke it. Should I get a type d core and use fii cubes or should I try ang glue. If I glue it will there be performance loss and will I be able to put the cubes back on without popping the glued plastic on the core
 
are you also using C4Y hardwares? I found that it didn't work too well on mine.
I have a gray core. But my hole body weight was on it so.... Anyway what do you recommend I do. Keep in mind my parents don't know I broke it. Should I get a type d core and use fii cubes or should I try ang glue. If I glue it will there be performance loss and will I be able to put the cubes back on without popping the glued plastic on the core

I say use the D/D-II (don't know if there is any significant difference) core + hardware (hardware is important, don't use your F-II ones.) if you have one. Otherwise, try gluing the core back together. If you glue it correctly, It should withstand popping out an edge. Maybe not corner cutting though.
 
What is hardware. So tell me exactly everything I have to buy including core, springs hardware(no clue what hardware is) and any miselanious(can't spell) items. Also tell me what to use from my fii
 
What is hardware. So tell me exactly everything I have to buy including core, springs hardware(no clue what hardware is) and any miselanious(can't spell) items. Also tell me what to use from my fii

Your F-II... hmmm, well, accoring to miniGOINGS, he's using C4Y core with New (gray core) F-II hardware (i assume it has gray core). Don't use the Blue cored hardware, as the screws are too long (because the core is smaller.)
Buy Type A Core and Hardware (screw/spring/washer) from Cubedepot. I recommend getting more than 1 set of each. Maybe 3.
If your F-II has a gray core, use that hardware with the Type A core. That should work... i think, since the Type A cores from Cubedepot are the same as D-II cores (that i'm using.)
If you order from Speedcubeshop, i think that they have C4Y cores there. I would recommend those over any core. They're really strong :)
Try getting C4Y hardware as well, they're pretty good.

Dillon, nope, but that reminds me about something! Thanks. :)
I hope that reminded you to try your F-II with C4Y hardware. I want to know how it goes. I've tried a F-II with one of those random cores and C4Y hardware. It didn't turn out well.
 
Last edited:
Back
Top