Nuber Cuber
Regular
- Joined
- Jun 3, 2008
- Messages
- 41
So today I finally got my shipment in from DealExtreme, I placed my order almost a full month ago (2/18). That's the first thing you should know about DX, it takes a long time to get the cubes shipped out. Anyway, that's not what I'm here to talk about.
Today when I unpacked the 4x4x4, I could tell it was going to need some work. I could barely apply a U turn finger trick. Then after playing with it for maybe 2 minutes, a red tile fell off. After picking it up again a few minutes later, a orange tile fell off. I could have pasted the tiles back on, but I have some cubesmith stickers that I just ordered for this cube. I knew that I was going to have to replace all of the tiles with stickers. Doesn't seem to hard, right? Wrong..
Here's what I ran across, either:
A. Some tiles will come off just with your fingers
B. Some tiles will require up to 10 minutes of picking at them with a flat head screwdriver
It took me at least 10 minutes to peel off one of the red tiles, and also gave me a cut on my index finger from a screwdriver slip.
Edit: Oh yeah, I also got the 3x3x3 from DX and the transparent Square-1. The 3x3 is amazing, and the square-1 turns nicely too.
Here's a little list of things you will need if you plan on getting your DX clone stickered and working well.
-Lots of time
-Flat head screwdriver
-Eye protection (I've been saved by my glasses 4 times already, these tiles tend to pop off right into your eyes) Think I'm kidding? Don't say I didn't warn you
-Silicon
-Band Aids (You are lucky if you don't end up getting cut at least once by a slipping screwdriver)
-Something to get globs of glue residue off of the cubies.
Also, when you pop off the tiles with a screwdriver, there is no telling where they will go. I will probably end up finding tiles years later scattered across my room, these things fly far.
So the moral of this story is, good luck restickering this thing, it's gonna take a while.
Also, I do no have any ideas on what will be the easiest way to get the glue of the cubies, there is quite a bit that is even hard to scrape off with a screwdriver. Putting stickers on right over this glue will result in an ugly bulge on each sticker. Please post if you have any ideas.
Also, I took off the top layer and sprayed the ball with silicone. It now turns about three times better, but could still use some work. I will probably end up spraying each piece individually if I am putting this much work into it already.
I want to clarify. THIS CUBE WILL BE VERY GOOD. It is just going to take a lot of work. I'm not making this to discourage buyers, I'm just explaining that it will take a lot of work and lubing.
Today when I unpacked the 4x4x4, I could tell it was going to need some work. I could barely apply a U turn finger trick. Then after playing with it for maybe 2 minutes, a red tile fell off. After picking it up again a few minutes later, a orange tile fell off. I could have pasted the tiles back on, but I have some cubesmith stickers that I just ordered for this cube. I knew that I was going to have to replace all of the tiles with stickers. Doesn't seem to hard, right? Wrong..
Here's what I ran across, either:
A. Some tiles will come off just with your fingers
B. Some tiles will require up to 10 minutes of picking at them with a flat head screwdriver
It took me at least 10 minutes to peel off one of the red tiles, and also gave me a cut on my index finger from a screwdriver slip.
Edit: Oh yeah, I also got the 3x3x3 from DX and the transparent Square-1. The 3x3 is amazing, and the square-1 turns nicely too.
Here's a little list of things you will need if you plan on getting your DX clone stickered and working well.
-Lots of time
-Flat head screwdriver
-Eye protection (I've been saved by my glasses 4 times already, these tiles tend to pop off right into your eyes) Think I'm kidding? Don't say I didn't warn you
-Silicon
-Band Aids (You are lucky if you don't end up getting cut at least once by a slipping screwdriver)
-Something to get globs of glue residue off of the cubies.
Also, when you pop off the tiles with a screwdriver, there is no telling where they will go. I will probably end up finding tiles years later scattered across my room, these things fly far.
So the moral of this story is, good luck restickering this thing, it's gonna take a while.
Also, I do no have any ideas on what will be the easiest way to get the glue of the cubies, there is quite a bit that is even hard to scrape off with a screwdriver. Putting stickers on right over this glue will result in an ugly bulge on each sticker. Please post if you have any ideas.
Also, I took off the top layer and sprayed the ball with silicone. It now turns about three times better, but could still use some work. I will probably end up spraying each piece individually if I am putting this much work into it already.
I want to clarify. THIS CUBE WILL BE VERY GOOD. It is just going to take a lot of work. I'm not making this to discourage buyers, I'm just explaining that it will take a lot of work and lubing.
Last edited: