V-Cube 4

Hard.. medium.. hard.. medium.

HRMPH.. ok.. using the mediums I would like to tighten them tensions a bit more but that isn't possible.
Using the hard ones I would like to loosen them tensions a bit more but then the screws eat away at the plastic.

Dilemma.

Add a washer to the mediums.. indeed.

I have a few sets of dayan zhanchi here, so.. grab washer.. put in, notice it dunnafitindahole.

Imagine my face. :rolleyes:

So if you want to add a washer, dayans won't fit. Even looked at the panshi. Nope.

Just out of the blue I grabbed my Gans cube. It has very small washers around a similar sized screw, and those DO fit. I wish they were thicker though, they're so thin. They do help a wee bit though, so they are staying in.


Also.. VERY important!! If you are changing out the springs and all.. take good care that your centerpiece does NOT twist so hold that down with a finger. You CAN screw it in backwards, the lips will bend out, and you wouldn't even know it until you start turning and the cube locks on you. SO be careful, you can damage your centerpieces that way. I found out in time, just wanted to throw out that warning.
 
Anybody get a flat but non DIY? What did the underside of your external center pieces look like?

Hmm, I've actually noticed that the inner corner of the centre pieces is actually wearing away slightly, I think this is potentially what's causing the roughness in the turning, and will probably break in over time, not entirely sure if it should be happening though :|

The "pi mod posts" are catching all sorts of ways they are not supposed to catch on the inner lip of the external center pieces for me. A temporary fix was to put some thicker lube on that inside lip of a few of them and then it worked around the posts and reduced the catching.

0SdEYPN.jpg

I think for a permanent fix that inner lip needs to be filled in or filed down.
 
Last edited by a moderator:
Oh that! Yes, I notice that too, but it isn't too bad for me. Of course my times are bleh on the 4x4 so that will be a factor. You could simply sand them flat .. I wouldn't fill them in because then the entire lip will do the catching.

On the flat.. don't file them down too much though.. you don't want the caps to break off after all :)
 
Last edited:
The back edge there is supposed to push against the posts on 50% of the center slices or whenever your turning two layers. The back stop takes the hidden centers along with one or another external centers. Filling in the underside lip would not be bad. I think the same part on the pillowed cubes is cast with that filled in. You would still get some smaller catching on the outside leading edge of the lip if that isn't also rounded off.

I think filing away the under side lip is probably the way to go. I just want to be cautious before modding this thing
 
Last edited:
Personally I'd try breaking it in some more first and see where it goes. I have done a few solves on it now and it improves a LOT.

Oh.. I want to get some washers that actually fit.. if anyone knows a place where I can get them and they fit (conical design of the hole, dayans do not fit, too wide) it would be great.
 
Because the spring and screw heads don't move against the plastic you don't have to put the washers at the bottom of the hole to protect the plastic. You could stack your dayan and other washers between the top of the spring and the underside of the screw head. Put them where the cone has widened out a little.
 
Last edited:
No workie. I tried that already ;) It is the first thing I thought of after seeing it didn't fit. You get an extremely loose cube if you do that.

The washer doesn't quite fit in the hole, leaving the screw up higher than before and thus the tension looser.
 
No workie. I tried that already ;) It is the first thing I thought of after seeing it didn't fit. You get an extremely loose cube if you do that.

The washer doesn't quite fit in the hole, leaving the screw up higher than before and thus the tension looser.

Something I did with my V5 to get these tighter tensions was coil a paperclip below the screw's head (I did 4 coils then cut it with wire cutters, but this depends on how tight you want it, the paperclip's thickness, etc.). It's effectively like stacking washers, and fits really nice if you do it right. I might be able to take pictures when I get home later, but yeah.
 
Oh a picture would be wonderful yes! Good idea too :)


Edit 8 hours later:
I tried this just now a few times, but I cannot get the rings made proper. They are mostly ending up too tight. I'll just opt for the washers or leave the cube as is. Thanks for the idea though, maybe someone who is more handy than I am will benefit :)
 
Last edited:
I'm going to do a big unboxing review video. I should finish filming this evening. I'm not rushing it.

Comparison of SS vs VCube 4:

We still don't have a perfect 4x4 both have problems.

Vcube is fast and cornet cuts line to line. Does not reverse corner cut at all. It makes you want to go fast but vcube has no anti-poping mechanism. This can be a really big deal especially for an even numbered cube. They should have stolen that anti-popping bits from SS or put the time into making their own. The way to avoid pops with the vcube is to pop pieces back in and tighten a little more, maybe use springs stiffer than what you really want. The flat vcube 4 seems a little more catchy on the outer layers, it doesn't seem as smooth and it's absolutely not as quiet as what I had seen from it's pillowed version. Inner slices are awesome. Still it's a high quality cube the hard plastic was cast very well and smooth, I only found one significant burr on all my parts. Even with all the things I have mentioned there is something very good about it. I just want to mod it, I think it screams mod me and for a cube this nice and expensive and prone to popping I wish that wasn't the case.

SS we know. we know middle slices can be bad. We know it's better modded. We know it's almost unpopable when put together right. I think all ss has to do to pull ahead with a new revision is use the inner layer control mechanism (pi-mod) from their 6x6 or from the vcube 4x4 and their slice problems would be greatly reduced.

Despite my complaints I think V cube wins right now. The The fundamental movement is smooth. Get rid of the catches and give it a tiny bit of reverse corner cutting with a florian mod and it will wipe the floor with SS.

Value per dollar? Shengshou. Being unpopable helps it be a safe cube that wins this.
 
Last edited:
My experience.. Inner slicing is perfect with the v-cube, not so on the SS. My v-cube hasn't popped yet, to get a piece out I have to go through some trouble alright. Corner cutting is 1 and 1/3 cubie so more than SenileGenXer's cube.

Quiet is something that takes a LOT of solves, but it will never be quiet, I find the sound on mine is the same as I heard on the stream (which was a pillowed).
 
How long did it take to get to you, SenileGenXer? From the time you ordered it? Also, glad to hear it may be better than the SS 4. I have yet to get a good 4x4. And my eastsheen broke
 
I found fitting washers! The ShengEn FII has washers that fit nice in this cube. I left the Gans cube washers in and I am off to tension again.. wait and see :)
 
I have an unboxing and review up on youtube. Watch me be tired and struggle to find the best words only to have them never come to me. Watch me do a very bad solve.

I say the same things I've said in this thread in fact I used one post for the description. 22 minutes.

 
Last edited by a moderator:
Oh god.. whahahahah I loooove how you start out that video!! ROFL!!!!


*goes watch the rest after she's done laughing*

:tu



Speaking of.. they forgot my invoice!


If you fill it in on those centers, do let us know how it fares.. I have milliput here that I can use.. so.. would love to hear :)
 
Last edited:
Really torn on this cube. Might just mod my shengshou some more and wait for the cube to make it to the US. Not sounding like a $50 cube yet :-) .
 
Back
Top