V-Cube 4

The Fangcuns caps come off easily and I´ve heard that putting a bit of lube under helps, it might be worth trying on the V-Cube if you don´t want to use glue.
 
I just wanted to let you all know.. I was suspecting this, but it is confirmed now: this cube does NOT respond well to differential oil like Traxxas. I didn't use much, but still. I have taken the cube entirely apart (save for the inner centers, left those on the core) and cleaned every single piece completely so there is no lube left in the cube. And boy does it turn so much better.

So be careful, even VERY little (and I am talking about a thin 1cm long line on one cubie and working that in) is too much. At least.. that is MY experience.

Maybe another lubricant works better on this cube, but I only have Traxxas.. so.. barren it stays from now on lol
 
I just wanted to let you all know.. I was suspecting this, but it is confirmed now: this cube does NOT respond well to differential oil like Traxxas. I didn't use much, but still. I have taken the cube entirely apart (save for the inner centers, left those on the core) and cleaned every single piece completely so there is no lube left in the cube. And boy does it turn so much better.

So be careful, even VERY little (and I am talking about a thin 1cm long line on one cubie and working that in) is too much. At least.. that is MY experience.

Maybe another lubricant works better on this cube, but I only have Traxxas.. so.. barren it stays from now on lol

What weight are you talking about? also can you still lube the core with differential oil?
 
10k weight.

Yes you can lube the core. I did that and that bit of lube is still in there. Not that it's much use actually since the core doesn't rotate at all.. but other than inside those centers where the springs and usually washers are there is NO lube on the cube. So not on those rings either, nowhere.

I used 10k before, even that was too much.

If you are experiencing a slower cube or tighter turning cube, you can at least try it.. take the whole dealie apart and clean it and put it back together. Lube is easily enough put back in if you don't like it :)
 
I'm a little bummed. I wanted to tighten my retail version flat black one and to my dismay the screws are already all the way in.
I'll have to replace the core or the screws to get it any tighter.

For those who are want to to glue caps on, I've heard Elmers white school glue is a good way to do it. It sticks but can be removed if needed.
 
I don't think I mentioned before, the holes in my core weren't straight and I had to pick the 6 least defective screws out of the 13 they gave me. A couple of the screws I didn't use had heads that couldn't have been more off centre without detaching from the thread.
 
Uhmm.. you had a DIY and the holes weren't straight?

There ARE no threaded holes in the DIY to begin with, you have to thread them yourself with the screws provided. Did you stick on the center pieces and screw them to the core in one go?

If so: that is where you went wrong. I posted a while ago to make the threads in the sides of the core without centers attached otherwise things can go lopsided. You have to be VERY meticulous when screwing them in for the first time.

As for the screws.. make pictures of them and mail verdes.. that is something they should fix alright!
 
Yep. I read your post and did what you said. I got the screws as straight as I could but the holes were too wonky to get the screws in any straighter =(
 
Then you probably went too fast on screwing them in. I had to back out and adjust them pretty much every mm of them going in, it took a LOOOONG time (and I mean that.. long..) but all my screws are in perfectly straight.

You COULD ask for a new core.. but.. I think you are going to have to pay for that one :/
 
It isn't the 1st cube I've assembled. The fact that I couldn't get a couple of the screws in straight is a reflection of how badly the core was made in the 1st place IMO.
If the holes were straight the screws would have gone in straight even if I tried to put them in slightly wonky. I did the best I could with the time (about an hour) and materials I was given.
I could fill the holes and redrill them but should I have to?
After all this isn't a 'cheap Chinese knockoff' to use Vs words. [/rant]
 
None. No lube at all. Read back to post #262

@cube-o-holic: Safe bet I did at least as many if not more, this isn't the first core to be like this. You can have this issue with cheap and expensive cubes.. you just have to be very careful and back up once you see it goes wonky. Dayan cores and other brands do this as well if you are not careful, so I am not writing this off to bad cores ;)


In fact, the issue with the misaligning and you having to make more effort TO get the screws in straight IS in fact the screws themselves. With Dayan screws nine times out of ten the start of the screw is flush. No thread. This allows you to stick the screw in a wee bit and only then it starts tapping the thread, resulting in nine times out of ten a good straight thread. Still you have to pay attention then.

The screws that this cube has are.. well.. not so handy in my opinion; they are screws, not bolts, which makes it one harder to tension and two much more difficult to thread the core with due to the larger "biting" distance between the threads. That was the only thing I was amazed at in fact.. that they weren't bolts but screws!
 
Last edited:
I have tried other weights, not doing that anymore either.

I don't have other lubes so no clue how that will work, but the cube is smooth enough for me for now :)
 
one or two drops of maru lube works really well but none might be a good place to start. You might want to break the cube in for a week without lube..

My screws were not great.
 
I was amazed, I have many kinds and brands of cubes, this is the first one that doesn't like lube. Weird. Good thing it is pretty ok out of the box, but I have this feeling that there is more in the cube that could come out, but not with traxxas lubix and such like lubes in any case. I might try Maru, the two drops, see if that does something.

SenileGenXer: would this be the kind you are talking about? I mean I am a lubix/traxxas person and I know dip about Maru lube lol
http://www.fasttech.com/products/2115/10002273/1165603-maru-lube-for-magic-cubes
 
Hmm I've been thinking about this for a couple of days now, I think that lubix would work just fine (or similar) but its more a question of where you put it in this cube than for most others.

I'm thinking that maybe between the inner midge and inner +centre could benefit the cube, and also on the base of the corners. I think the way the mech is held together will stop the lube from moving around as much, so where you put it matters much more. I'll try this in a bit and get back to you with the results.
 
Back
Top