V-Cube 4

I have no clue. Might want to mail verdes on that one :) I'd say go for a DIY, OR try and get two more sets of springs along with the ready made one.. the prices are the same, so.. in theory.. yadda yadda no prob etc. In theory :)

yes I guess I will order the DIY version =)

Video is up!


I liked it a lot , but I don't own a SS 4x4 so I can't judge , so is it better than a SS 4x4 or not ? I'm mainly talking about lock ups and slice moves :)
 
Last edited by a moderator:
then I will have to wait until masterofthebass do his review :) I will mainly use it for BLD so lock ups and slice moves are what concern me the most , thanks anyway =)

Ah ok, well the slice moves are very good imo, and it doesn't really lockup that much. Mine does a little bit atm but I only notice during scrambling and the tensions aren't totally set right yet. I haven't tried a 4BLD with it yet, but I will soon, and I think it will be good for it.
 
Thanks!!

I can see in the vid that it is a good cube. Unfortunately I cannot differentiate the talking over the cubing sounds so.. I hear you go blahblah but not a CLUE what the blahblah is LOL! Not your fault, it's my hearing, but I see above your conclusions.

I have found that tightening up the tensions a wee bit reduce the lockups which in theory on that aspect makes it behave like a big cube.

Which springs did you use?
 
Thanks!!

I can see in the vid that it is a good cube. Unfortunately I cannot differentiate the talking over the cubing sounds so.. I hear you go blahblah but not a CLUE what the blahblah is LOL! Not your fault, it's my hearing, but I see above your conclusions.

I have found that tightening up the tensions a wee bit reduce the lockups which in theory on that aspect makes it behave like a big cube.

Which springs did you use?

I'm using the heaviest springs atm. I'm still playing around with the tensions and I'm sure I'll get it to where I like it, but it seems to be quite twitchy on tensions.
 
I got mine yesterday, but the centers pieces keep catching on the extensions on the core pieces (PI-mod)
I think it's probably because they didn't cap the center pieces, you can see that on the picture from Kattenvriendin
So I can't get good times on the cube... any way to fix this (I didn't get the DIY cube...I'm lazy)


Center
center.jpg
 
The only way to get the centers to go down in the cube is to tighten the tensions.

If you cannot do that you can try shortening the springs one loop (nope!), or better yet.. I'd say mail Verdes and tell them that you need softer (nope!) springs than what is in there.

Also.. you could try and get 6 pens with springs and hope that works. I wouldn't go cutting them springs in any case till you hear from Verdes.


Edit: waaait a second.. noo.. don't shorten the springs.. you actually need longer springs or harder ones! I was brushing my teeth and had a clear moment (imagine me spitting the stuff out and running back here to add this lol!)

You need for the springs to push the center piece further down in relation to the screw. The exact opposite of what I had where the screw was sticking up too much and I had to insert a softer spring to get the centerpiece to raise above the screw (or rather for the screw to go in deeper).

So maybe that pen springs idea could work as those springs are often longer, just depends on the stiffness then.


I am going to start playing with my cube today and see how I like it with the softer springs, and if that is all ok I could send you my harder ones if you like?
 
Last edited:
thank you for the tips! I have a lot of different type of springs at home...I will play around with it.
I was also thinking about filling in the gaps on the center pieces or maybe doing some work on them with sandpaper to round it of a little bit.
 
Hmm, I've actually noticed that the inner corner of the centre pieces is actually wearing away slightly, I think this is potentially what's causing the roughness in the turning, and will probably break in over time, not entirely sure if it should be happening though :|
 
Take a look at the screws.. is there powder in your cube color on it? If so, then the screws are sticking up too far compared to the center piece and you will have to go one step softer on the springs to sort this out. It sorted it for me in any case.
 
thats exactly what i need. i hate shengshou's lock ups, even after mod.

btw bleach is awesome
My shengshou never locked up. What are you talking about?

PS: My SS has no lube or such thing, and it's PERFECTLY tensioned.
 
I received mine this morning. Jumped out of the shower and accosted the fleeing UPS man while I was wearing only my towel and everything.

I have to do some adult things like work and enter more info into taxes and I am waiting to do a nice unboxing video/review and a separate assembly guide. So it's taking lots of self control today not to open this today.

Are the snap together pieces holding together or should I buy some plastic glue from a hobby shop?
 
Take a look at the screws.. is there powder in your cube color on it? If so, then the screws are sticking up too far compared to the center piece and you will have to go one step softer on the springs to sort this out. It sorted it for me in any case.

Hmm, I might try that, I kind of like it as it is for now, but I might change over just to see if I prefer it.

Are the snap together pieces holding together or should I buy some plastic glue from a hobby shop?

They hold together really well. I've only had 1 piece come apart, and it was a cap on a centre. They're pretty solid really.
 
Back
Top