DaYan + mf8 4x4

jla

Veteran
Joined
Aug 31, 2010
Messages
326
Location
Gothenburg, Sweden
WCA ID
2011LANG01
YouTube
Visit Channel
Hi!

I bought a DaYan +mf8 4x4 a while back ago but it doesn't turn as good as I've seen others. I have lubed the inner 2x2 core with crc and that maked the inner layers a little bit less stiff but the cube still has a clicky feel and isn't smooth at all. I know this is the cube Feliks used for his world record but I seriously need help with making my cube better.

Thank you in advance

/jla

EDIT: And by clicky feel I mean that the cube gets stiffer in the middle of a turn and if I would take a finger and turn a layer around it would stop for maybe .25 seconds and then work again

Thank's again
 
1. Don't tighten the black parts of the second ball completely; This will make it much quicker and smoother but will make the cube feel like it's going to pop heaps easier. I have mine about 1.5-2 screw turns from max tightness.

2. It'll get much better over time with the more solves you do :).
 
1. Change the 3x3 core into C4U core (optional)
2. Change the spring into YJ 3x3 VVGOO-II / LanLan 2x2 spring, and tighten your cube tension (recommended, because YJ/Lanlan spring is soft and it will make your Dayan turn smoother and faster even if the tension is tight. So it much more popless).
3. Change the screw into YJ 3x3 VVGOO-II / Lanlan 2x2 Screw (optional, but i recommended it)


Hope it will help you, and sorry for bad english..
 
1. Change the 3x3 core into C4U core (optional)
2. Change the spring into YJ 3x3 VVGOO-II / LanLan 2x2 spring, and tighten your cube tension (recommended, because YJ/Lanlan spring is soft and it will make your Dayan turn smoother and faster even if the tension is tight. So it much more popless).
3. Change the screw into YJ 3x3 VVGOO-II / Lanlan 2x2 Screw (optional, but i recommended it)


Hope it will help you, and sorry for bad english..

I did that last night, i now officialy love 4x4ing.
if anybody has a lanlan 2x2 they dont use and a dayan 4x4, DO THIS MOD!!! :D
 
What should I lube it with, is it worth to buy maru lube for it??

Use Lubix / diff. oil for the inner core. You can use silicone spray and/or Maru lube for the pieces themselves.
 
I replaced the screws (for the 2x2 part) with ghost hand 2x2 screws (people say lanlan screws, but one of my lanlan screws are messed up, so I just did GH 2x2 screw), and I replaced the springs with lanaln 2x2 springs. I also replaced the 2x2 edges with lanlan 2x2 inner edges. Ten I removed a little excess plastic off of the mf8+dayan 2x2 corners, and lubed the screws+springs, and the core with lubix izo-lube (lubix type-stuff). After messing around with the tensions, it became a lot faster (inner and outer layers), and didn't pop as much.

EDIT: I may even make a tutorial for this sometime.
 
I replaced the screws (for the 2x2 part) with ghost hand 2x2 screws (people say lanlan screws, but one of my lanlan screws are messed up, so I just did GH 2x2 screw), and I replaced the springs with lanaln 2x2 springs. I also replaced the 2x2 edges with lanlan 2x2 inner edges. Ten I removed a little excess plastic off of the mf8+dayan 2x2 corners, and lubed the screws+springs, and the core with lubix izo-lube (lubix type-stuff). After messing around with the tensions, it became a lot faster (inner and outer layers), and didn't pop as much.

EDIT: I may even make a tutorial for this sometime.

please make a tutorial


as a side note if there is a tut already can someone link me?
 
Back
Top