GuHong: defect or bad assembly?

did u get it from lightake? http://www.lightake.com/detail.do/sku._3x3x3_DaYan_GuHong_Magic_Cube_DIY_Kit_Black_-30597
not sure why its so cheap compared to the other guhongs. fake?

I'm not sure of the supplier it came from, I bought two from Cube Depot, I'm not sure where he gets them though.

Both the Guhongs I got are legit I think, they are very nice except the corner seams being off. What I did notice though is each one of mine seems to be made of a slightly different grade of plastic. Both are made of good plastic, just one of them is a little more translucent and more 'slippery'. It's weird. :D Both white ones btw.

Edit: also, this is probably just normal I think. It's very hard to achieve perfect accuracy in production in the way that the design requires. Making three edges meet like that with mass produced parts can be difficult, because even an 'nth of a degree difference that you can't even see with your eye can throw it off, unless tolerances are accounted for in the design of the parts.
 
Last edited:
I'm not sure of the supplier it came from, I bought two from Cube Depot, I'm not sure where he gets them though.

Both the Guhongs I got are legit I think, they are very nice except the corner seams being off. What I did notice though is each one of mine seems to be made of a slightly different grade of plastic. Both are made of good plastic, just one of them is a little more translucent and more 'slippery'. It's weird. :D Both white ones btw.

when did u get ur guhongs? the 8$ ones on lightake just came out a few days ago
 
when did u get ur guhongs? the 8$ ones on lightake just came out a few days ago

Ordered them at the end of last month I think, so I don't think it was those. And they were DIY's so that may be a factor since the parts were free in the package, some extra warping might have happened in storage and shipping.
 
Ordered them at the end of last month I think, so I don't think it was those. And they were DIY's so that may be a factor since the parts were free in the package, some extra warping might have happened in storage and shipping.

i havent ordered the 8$ ones yet since it seems a bit sketchy
they are diy also but idk how they are packaged
 
i havent ordered the 8$ ones yet since it seems a bit sketchy
they are diy also but idk how they are packaged

Every DIY I've seen so far is just parts removed from the sprue, trimmed, and shoved in a ziplock bag. Not the best practice IMO, but it's cheap and allows the parts to at least be inspected (unless they are dumped in by machine, which I highly doubt)
 
The tri tab thing made me rethink a bit, and after a couple experiments, I found that I was at least partly wrong. But I did discover a possible way to fix the corners.

I took apart my rubenking Guhong that still had this problem quite badly and tried to figure it out. I found on some corners, if you take it apart, rotate the tri tab in the main body of the corner by one peg (take the peg out of the hole and put the peg next to it in the same hole) and put it back together and test the fit, it may eliminate the problem. If not, try one more turn of the peg.

I managed to make all corners except one on my rubenking seal up nearly perfect by doing this.

Great information, thanks! When I run into the gap problem when assembling the pieces, I'd usually just swap corner pieces or tri-tabs to fix the alignment. I've had your way fix the gap issue several times now.

- Pixel -
 
I bet that is caused by bad assembly. I think that if you continue cubing on this, the tiles might fall off which would irritate you more. May i ask where you got this? Maybe you could try to report it and refer to your order if the supplier accepts returns for defects. Better act fast as they might not accept it if time has already passed.
 
Back
Top