GuHong: defect or bad assembly?

Xnx

Regular
Joined
Feb 21, 2011
Messages
36
I've just got my GuHong and it came preassembled. One thing I immediately noticed was that some corners had little gaps where the three parts come together on the outer side. One or two corners look fine, however others do not. From all the videos/photos I've seen none of the GuHongs had that. I even tried taking the corner apart and putting it back together, however that didn't seem to help either. Is it a defect or do all of them have this only it's not seen in the videos? Or maybe I am doing something wrong? :confused:

img031t.jpg

img037v.jpg

img039dd.jpg
 
Last edited:
Had a couple like that, maybe not quite as bad but they did settle. You made sure the internal connectors have the little raised parts pointing towards the inside of the piece top and bottom?

Can be a worse problem on Lingyun to be honest with the 'wing' piece connectors.
 
I had a Lubix guhong that looked perfect, but when I bought a spare Guhong from Lightake I was surprised to see these gaps (especially since I hadn't realised there were separate bits of plastic in the corner). I just kept giving them a squeeze and they seemed to be fine.
You said you tried taking them apart and putting them together again... have you tried swapping a few of the bits around between corners to see if they fit better?
 
Had a couple like that, maybe not quite as bad but they did settle. You made sure the internal connectors have the little raised parts pointing towards the inside of the piece top and bottom?
Can be a worse problem on Lingyun to be honest with the 'wing' piece connectors.

2nd. I made that mistake once.
 
Yes, all the connectors' bumps are pointing inwards.

I did try switching the parts around a bit and it does actually seem like it has improved a bit, yet there still are some gaps left and they're just driving me crazy.
 
Mine started out like this. It is mainly due to the fact that the seam edges themselves aren't internally braced, and the either the surfaces aren't perfectly straight or the edges of the three pieces that fit together aren't perfectly straight.

On my regular Guhong that I use a lot, this has slowly diminished by itself just by using it a lot and slowly reforming the plastic, I think, but it is still there very slightly. There's really nothing to keep those edges together, it depends on the plastic being perfectly straight for them to meet flush. The little tri pins inside don't have much to do with it if they are inserted properly and completely.

Edit: also this shouldn't effect how it solves, it's mostly cosmetic.
 
I had this same "problem" on my stickerless guhong, and I got another one. The second one had slightly smaller gaps, and neither one seemed weird or different in terms of solving. You really only have the cosmetic factor, and you won't notice it when your solving it :P

PS: Does anyone know where I can get CRC in the West LA/Santa Monica area?
 
Last edited:
Mind has this, too, and I just figured it was something more prevalent in the white cubes because you're not as likely to see it in a black one. I figure it will settle.
 
If it's bothering you that much, you could always glue the pieces together from the inside with krazy glue or something like that... But there's really no point because the gaps aren't affecting the cube's performance.
 
lol push the corner pieces together.

Thanks, I really thought you could just lay it down on the table and wait for it to magically come together. You've saved my life!


The gaps are smaller now after changing the pieces around, I suppose it's bearable. You can't really see them while solving anyway. Oh well, glad to hear it's not something out of the ordinary, thanks for the feedback.
 
The pictures in the OP actually load when I open the thread now. They weren't loading yesterday so I was assuming you were talking about the corner stalks not going together seamlessly. Sorry :( What you have there is normal though. I have it on my three GuHongs too. My two LingYun cubes fit together seamlessly but their construction method is more sturdy, so yeah...
 
I had a Lubix guhong that looked perfect, but when I bought a spare Guhong from Lightake I was surprised to see these gaps (especially since I hadn't realised there were separate bits of plastic in the corner). I just kept giving them a squeeze and they seemed to be fine.
You said you tried taking them apart and putting them together again... have you tried swapping a few of the bits around between corners to see if they fit better?

Donovan said in one of his posts he sands down the tri-tabs, this is normal to find a corner like this. I bought a DIY POM kit from lightake, when I assembled it, it looked like this. Do not worry as this is normal!
 
The tri tab thing made me rethink a bit, and after a couple experiments, I found that I was at least partly wrong. But I did discover a possible way to fix the corners.

I took apart my rubenking Guhong that still had this problem quite badly and tried to figure it out. I found on some corners, if you take it apart, rotate the tri tab in the main body of the corner by one peg (take the peg out of the hole and put the peg next to it in the same hole) and put it back together and test the fit, it may eliminate the problem. If not, try one more turn of the peg.

I managed to make all corners except one on my rubenking seal up nearly perfect by doing this.
 
The tri tab thing made me rethink a bit, and after a couple experiments, I found that I was at least partly wrong. But I did discover a possible way to fix the corners.

I took apart my rubenking Guhong that still had this problem quite badly and tried to figure it out. I found on some corners, if you take it apart, rotate the tri tab in the main body of the corner by one peg (take the peg out of the hole and put the peg next to it in the same hole) and put it back together and test the fit, it may eliminate the problem. If not, try one more turn of the peg.

I managed to make all corners except one on my rubenking seal up nearly perfect by doing this.

did u get it from lightake? http://www.lightake.com/detail.do/sku._3x3x3_DaYan_GuHong_Magic_Cube_DIY_Kit_Black_-30597
not sure why its so cheap compared to the other guhongs. fake?
 
Back
Top