stackmat analysis mode

Analysis results

Could this help with determining an acceptable level of sensitivity for timers that are to be used in a competition?

Perhaps the data from it might also indicate whether the timer is likely to malfunction (~0.2 etc).

Code:
Mon Year No No-light Red      Green    No-light
--- ---- -- -------- -------- -------- --------
Mar 2008 #1 N/A      0187     016E     N/A
Apr 2008 #1 N/A      0185     022E     N/A
Mar 2009 #1 N/A      0220     0220     N/A
Apr 2009 #1 N/A      0245     0238     N/A

Tim.
 
Last edited:
I only have two modes:

1) Red light on. Default around 0226. Left hand on pad makes it go down by about 3, right hand to about 01d0. Both hands about 01bE, palms about 0177.
2) Green light on. Default around 021d. Right hand on pad makes it go down by about 3, left hand to about 01C8. Both hands get about 01A0, palms get about 0173

Stackmat DATE: March 2009
 
This is interesting.

Red gives 0225
Green gives 021A

Holding down red normally gives 017A
Holding down green normally gives 016D

Holding down red hard gives 01CE
Holding down green hard gives 01CB

My stackmat is from April 2009.
 
Mine's January 2010, and only cycles between green and red.
it's GREAT, i could press hard and the red one shows... 198.
 
Stefan, when you use your hand to start the timer, are you just touching the two metal prongs on the inside? I am referring to when you have the PCB out of the stackmat plastic casing (normally referred to as chassis).

aronpm: What do you mean by holding down red/green hard/normal? Do you mean holding down on the touch pad hard and with the the red/green lights selected it shows you those values? Or holding down something else hard?

So I was typing in my stats but I noticed that the numbers change from fingertips to palm, to pressing lightly, harder, and real hard, etc. I could have recorded all the values but if I move my hand a quarter of an inch, it will change the value, so I gave up.
 
aronpm: What do you mean by holding down red/green hard/normal? Do you mean holding down on the touch pad hard and with the the red/green lights selected it shows you those values? Or holding down something else hard?
I meant holding down normally, as if I were doing a solve. Hard was pushing the pads as hard as I could.
 
New record! I can now cause a reaction from about 60 cm (2 feet) away! Take a deep breath, breathe inside your closed mouth a couple of times to make the air warmer and more humid, then strongly breathe out onto the timer. Only a small effect, like from 01F3 to 01F2, but I can do it consistently.

Now I just need to build a device to allow a stronger effect from an even larger distance so I can remote control the timers and disqualify everyone faster than me by stopping their timers at like 0.20 seconds...

Stefan, when you use your hand to start the timer, are you just touching the two metal prongs on the inside?

In the video? Well, I'm also holding the thing at other places, but yes, I think touching those metal things on the sides is what it reacts to.
 
Man I was looking at your pictures of the board but I wasn't able to see what they connect to (via the traces). I follow what seems like the path going to and from the black pieces and it connects to nothing. I might need to open mine up for a closer look or something.

I wonder if there's a way we could analyze exactly how much we need the number to change to start/stop the timer. We could probably set up two stackmats to each each other, using the same touchpad for both things.
 
date: July 2010
Red light: 0272
Green light: 0267

I can only cycle trough green and red.
The numbers seems to change. Can anyone explain what these values are?
 
Back
Top