CRC, its adverse effects, impressions and questions

super_speler

Member
Joined
Feb 5, 2010
Messages
11
After learning to solve it for the first time, I decided to lubricate my cube with Vaseline (*gasp*). Despite all the warnings, it did in fact help the cube move faster and smoother. All in all, I was happy with what I had. It might have been just me, but after a while, it started to turn slower and felt really rough in general. I decided to clean out my cube to try and alleviate the problem, but that only resulted in a cube just as bad as when I first bought it.

Finally giving up on trying to even turn the thing, I went out and bought a can of CRC Heavy Duty Silicone, due to its apparent popularity in the cubing community. After reading about lubrication using CRC and watching a few Youtube videos, I finally got to actually lubing my cube.

Copying badmephisto in his video, I popped two edges, sprayed in the CRC (two quick bursts each), popped the edges back in, and started to work it in. But then..

At first, turning it was pretty normal. However, the next few turns, it started to feel like I put glue in the cube - Turning it required tons of effort. Not only that, but below it, black specks started falling out of my cube, which I'm sure isn't the best thing for it. Too late to turn back, I just kept on working the CRC in and after a while, it began turning smoothly and faster than before.

I was satisfied with the end result, but disassembling my cube again, I found that the inside was pretty much devastated. Scratching the plastic scraped it off, and it was just plain ugly. The core is the only part that didn't seem to be affected.

IMG_1521.JPG


IMG_1526.JPG
IMG_1527.JPG


My question is, is this normal? If I get new cubes and decide to lubricate them with CRC, will it have the same effects? Because given the popularity of CRC, I was hoping for something a bit, say, cleaner.
 
After learning to solve it for the first time, I decided to lubricate my cube with Vaseline (*gasp*). Despite all the warnings, it did in fact help the cube move faster and smoother. All in all, I was happy with what I had. It might have been just me, but after a while, it started to turn slower and felt really rough in general. I decided to clean out my cube to try and alleviate the problem, but that only resulted in a cube just as bad as when I first bought it.

Finally giving up on trying to even turn the thing, I went out and bought a can of CRC Heavy Duty Silicone, due to its apparent popularity in the cubing community. After reading about lubrication using CRC and watching a few Youtube videos, I finally got to actually lubing my cube.

Copying badmephisto in his video, I popped two edges, sprayed in the CRC (two quick bursts each), popped the edges back in, and started to work it in. But then..

At first, turning it was pretty normal. However, the next few turns, it started to feel like I put glue in the cube - Turning it required tons of effort. Not only that, but below it, black specks started falling out of my cube, which I'm sure isn't the best thing for it. Too late to turn back, I just kept on working the CRC in and after a while, it began turning smoothly and faster than before.

I was satisfied with the end result, but disassembling my cube again, I found that the inside was pretty much devastated. Scratching the plastic scraped it off, and it was just plain ugly. The core is the only part that didn't seem to be affected.

IMG_1521.JPG


IMG_1526.JPG
IMG_1527.JPG


My question is, is this normal? If I get new cubes and decide to lubricate them with CRC, will it have the same effects? Because given the popularity of CRC, I was hoping for something a bit, say, cleaner.

if that is a type F .............then that is normal with CRC........
I use CRC for all my cubes type A,C,CII,F,and Edison ......
and I get that white build the most on my type F......... but all my cubes turn great though.........

also if your cube isnt clean before you lube it ....you should clean or you get like double the residue build up dirt/dust mixing with silicone
 
I guess it's safe to say that I'm new to cubing - 4 weeks. What you see is a normal storebought Rubik's cube. I was hoping the logo was obvious enough.
 
You may have cleaned it as clean as possible, but still not enough. The vasaline has weakened the plastic a lot and eaten it away. Spraying silicone in it after that makes it turn like superglue when it hasn't dried up yet,
 
I disagree with all this. I have sprayed CRC into brand new storeboughts fresh out of the package, and they almost always look pretty much just like this. They feel like glue was sprayed into them, they drop bits of black dust out when you turn them, and it feels like you ruined them. I keep turning for 10 or 15 minutes, and suddenly they start working like a dream. But they wind up still looking like this. It seems pretty likely to me that the acetone from the CRC melted the cube a bit, and it stuck together, but by continuously turning it, it keeps it from locking up, and eventually the silicone does its magic.

I would imagine if I took the cube apart and sprayed it, it might do better (although I still suspect it would melt the cube a bit), but when I do it this way, it still works pretty well, and it's a lot easier.

I have found recently that if I first put in CubeLube (the Johnson's wax stuff), and then wait a day or two before putting in CRC, it tends to eat the cube less. At least, it seems that way to me, but it could just be because I expect it to help.

Anyway, nothing you've seen here surprises me, it's what I always see with storeboughts (which is what most of my cubes are).
 
You must clean out your cube of vaseline completely before adding any other lubricant. That accounts for some of the grime falling out. However, as noted before, this is normal with CRC.

I don't know why people bash Jig-a-Loo for fusing pieces when CRC clearly does the same thing if you're not careful. What I like about Jig-a-Loo is that you can immediately feel the difference. I work my cube in for 30 seconds and every second is better than the previous. Then I solve it and its done, while with CRC you must work it for a while and leaves all sorts of nasty junk in your cube. Just my rant for the day...
 
the reason why storeboughts creates the most dusts is because of its tight tension. it's pretty obvious, i wonder why does nobody notice about this?
 
I bought a can of CRC once and had the white crap all over my cube too. Never used that stuff again. Went back to using Jig-a-loo and never looked back.
 
thrawst made a video about this. when your cube is like that, its cube cleaning time.

Its probably good too, since all cubes need to get cleaned eventually
 
This always happened when I sprayed in CRC (I use PrimeFlo now). I thought it might be the propellants in the spray, so I've tried applying the CRC with a Q-Tip. That seemed to help but it still does seem to frost the plastic.

Bill
 
Back
Top