Which PLL is your fastest

[Deleted member 36445]

Ja then hperm
this poll should have the 21 plls
EDIT: I checked maximum options for poll is 20...

 

[Eli Apperson]

It isn't. I have the WB for Ub with a 0.466 framecounted execution, which is only 1 frame faster than 0.500 flat. It was very difficult to get that.
Getting sub 0.6 consistently is easy though.

Ok now for my fastest PLL's.

My fastest is Ua, with the RUS alg I could probably get 0.400 flat (12 frames) but I'm too lazy to do that. My fastest recorded time is 0.466 framecounted (tied with Ub)

My fastest (and favorite!) PLL relative to others is Gc. I have a 0.66 framecounted Gc execution (two, in fact), which is a whopping 0.12 faster than the WB2.

My highest TPS PLL's are E (21.8 TPS), Jb (21.7 TPS), T (21.0 TPS) Y (20.4 TPS), and Ga (20.5 TPS)

Yeah sub .6 is probably more realistic. Ik quite a few people including myself who can get sub .5 relatively consistently.

 

[ruffleduck]

Ik quite a few people including myself who can get sub .5 relatively consistently.

Not framecounted, I'm assuming. Stackmat is usually 0.1-0.2 off the actual time

 

[Cuberstache]

Ja and Jb are tied for my best at 0.80

 

[xyzzy]

this poll should have the 21 plls
EDIT: I checked maximum options for poll is 20...

Which PLL do we vote off the island? One of the N perms?

 

[Deleted member 36445]

Which PLL do we vote off the island? One of the N perms?

I just stated that 21 was not an option, not deciding anything...

 

[qwr]

Which PLL do we vote off the island? One of the N perms?

both, then remove V and F for good measure

 

[Brouxt Force]

Ua, Ub, Aa, Jb, Ja, Ab, H, and then every other PLL takes 1+ seconds to execute. I haven't timed my PLLs in months, so I could definitely execute them faster. I'm not going to be timing my PLLs for a while, though, because I use Roux, where the fastest CMLLs are faster than the fastest PLLs (I can consistently execute sune in less than 0.5s). #Rouxvolution

 

[Waffles]

LUS U perms are too slow to be worth it if you're righty dominant

Ok; I’m not actually ambidextrous or right hand dominant; I use left hand for throwing and cubing and stuff, and my right hand for writing. I use a mix of R and L moves in my algs (most olls are L) so, theoretically I could actually use LUS U perms.

Which PLL do we vote off the island? One of the N perms?

Na. Only PLL I haven’t sub 1.5ed yet. Ik some people have sub 1 Na perm, which is just incredible. Once I get sub 1.5 with Na perm I will have no need to cube anymore be extremely happy.

First: Na
Next: Nb
Third: F
Fourth: V
Fifth: Gb

 

[falsnn]

Could you not have just renamed the old thread and added more options to the poll?

no cause it was only meant to be between T and J

 

[ruffleduck]

Na. Only PLL I haven’t sub 1.5ed yet. Ik some people have sub 1 Na perm, which is just incredible.

Na is definitely better than Nb. I did the zRUD alg in 0.767, compared to Nb which I can't sub 0.9 with zRUD.
For speedsolving Na is faster as well. L' F' U L U' L' U' F L2 F L' U' L' U L F' (which is often written in rDUF gen) is worse than R F U' R' U R U F' R2' F' R U R U' R' F because they're the same alg (except mirrored) but Nb has gripshift

 

[abunickabhi]

Surprisingly for me, H perm is the fastest PLL. Since I do BLD a lot, my M slice flick is the fastest.

 

[xyzzy]

I did the zRUD alg in 0.767, compared to Nb which I can't sub 0.9 with zRUD.

Does that include the z rotations?

 

[Brouxt Force]

Surprisingly for me, H perm is the fastest PLL. Since I do BLD a lot, my M slice flick is the fastest.

Do you use the MU U perms?

 

[abunickabhi]

Do you use the MU U perms?

Yes on 3x3.

On big cubes I use RU U perms.

 

[Cubing Forever]

Does that include the z rotations?

Afaik, nope. Rotations at the start and end of algs are ignored while framecounting.

 

[Megaminx lover]

Remove Nb and Ga add skip

 

[Waffles]

Remove Nb and Ga add skip

Ga? That’s not even in my bottom 7. Remove Nb, Na, F and V

 

[ruffleduck]

Does that include the z rotations?

No, rotation would probably add on around 0.2

Remove Nb and Ga add skip

Ga is quite good. After Gc, Ga is the fastest G perm for me.

 

[hellocubers]

change my mind. U PERM (b)