[Help Thread] Spring noise

MYKE

Regular
Joined
May 27, 2007
Messages
105
Location
HEXHAM, UK.
YouTube
Visit Channel
when ever i turn the blue side of my cube it sounds like the spring is cought on something givving it a "chinkling" or a "kin-kin-kin-kin" noise?

what is it?
 
i like that sound :) no idea what it is. Interestingly enough, I have exact same case on one of my old cubes and also on the blue face :)
 
I think the sound is due to the spring snapping out of shape when you twist it because it's compressed too much. Normally when you press a spring down the gaps close but if you continue then you'll find that it goes into the shape of an arch or an "S". When you twist a spring that's in this shape it'll make a bit of noise...
 
Noisy springs

I have a store-bought Rubik's cube that I can hardly stand to use because it has noisy springs. I bought two DIY cubes awhile back and one of the great things about them is how quiet the springs are. I wanted one more DIY. So I bought a Type A from cubefans, and recently put it together. It has a noisy spring! Argh.

Is there a way to quiet noisy springs?

By the way, my quiet cubes did not come from cubefans. One was from Puzzleproz and one was purchased from someone in the states and I'm not sure where he got it.
 
My storebought too had noisy springs.But after a month of cubing,there was no noise(except for the sound produced by cubies rubbing on each other;quite loud). Maybe because, I had lubed the cube (cubies & the core),with vaseline?
Or is it a part of the "breaking in" process?

Edit: Actually, the sound of the spring hasn't completely gone away,though it has reduced considerably.It is just that while turning, the cubies makes lot more sound than the springs.
 
Last edited:
My icon cube has this problem. I lubed it after like 3 days of really intense use (I hardly put it down!), and the springs are loud. It sucks to use especially when its quiet. I don't know what causes this but it is annoying -_-
 
The reason why you hear noise is because the springs are rubbing against the plastic/screw. Put in the springs again and again as balanced as you can until you can't hear the spring noise anymore. It might take more than 5 tries.
 
Before Cube Fan gave his advice I popped the cube apart, removed the caps, and loosened each screw. Then I put it back together and lubed it. Now it still has some spring noise but not as bad. If it starts bugging me, I will try Cube Fan's advice. In the meantime, if any of the rest of you that have noisy springs try his advice, it would be nice to get some feedback here. And of course if anyone else has other solutions, let us know.

Thanks.
 
does anyone else notice that the face with the noisy springs also has different tension than the other faces? I have this problem with two faces on my cube and both of them are "tighter" to turn than my other faces which are much smoother and don't make noise.

I'll try reseating the springs and see if I can't find out how they're currently sitting in case I can see why the springs may be misbehaving in their current state
 
Two springs on mine sdo that. IT makes a horrible noise, now everone hates that noise...Ima try C ubefans trick too, thanks
 
I've noticed each washer has a flat side and a slightly rounded side. I put the rounded side outward and the flat side against the spring. I also make sure the screws are not curved. I think the sound is at an end of a spring, where it catches onto the rounded edge of a washer.
 
I've noticed each washer has a flat side and a slightly rounded side. I put the rounded side outward and the flat side against the spring. I also make sure the screws are not curved. I think the sound is at an end of a spring, where it catches onto the rounded edge of a washer.
What if you cube doesn't have washers?

I use old Type D cubes - they don't need washers, and I can still make the springy sound go away.
 
well i opened mine up last night... in my case I think it's a combination of washer issues and spring issues. one of my small washers had a rather large piece of flashing on it (that I somehow missed when putting the cube together the first time) and that center piece had a *lot* of metal dust inside of it after only a week's use. I had originally followed the instructions provided by PuzzleProz, since I bought from him, and he recommended putting the rounded edges of the washers facing the spring since they tend to be SMOOTHER even if not flat, since the flat sides can have minor flashing. In my case the flashing was facing the core and was just grinding itself away in time - I took it out and filed it down myself though, then put it back in still with the rounded side facing the spring.

On that same center piece I did also notice that one end of my spring was not quite made properly or had been malformed at some point, and the one side of the spring wasn't "flat" - if I tried to stand the spring up, it would have worked on one side but the other side would have been more like the Leaning Tower of Pisa ;) I believe that "tilt" of the spring edge was causing much of the spring noise I had been hearing, since it wouldn't surprise me if the very end of the spring was being twisted around by the pressure of the washer which would cause it to spin in place rather than simply doing it's job of providing tension for the center piece and not moving, allowing the washers to spin AGAINST it. (I hope this makes sense to someone)

I tried to bend the bottom of the spring as best I could to adjust how it was positioned, and when I put everything back together and lubed it all up again I didn't have any noise coming from the springs anymore. I think I may need to file some of the extra flashing off the plastic on my cubies a bit, but that's another topic entirely ;)

Anyway I hope that helps someone. If anyone finds something similar or needs me to clarify anything just let me know.
 
well i opened mine up last night... in my case I think it's a combination of washer issues and spring issues. one of my small washers had a rather large piece of flashing on it (that I somehow missed when putting the cube together the first time) and that center piece had a *lot* of metal dust inside of it after only a week's use. I had originally followed the instructions provided by PuzzleProz, since I bought from him, and he recommended putting the rounded edges of the washers facing the spring since they tend to be SMOOTHER even if not flat, since the flat sides can have minor flashing. In my case the flashing was facing the core and was just grinding itself away in time - I took it out and filed it down myself though, then put it back in still with the rounded side facing the spring.

On that same center piece I did also notice that one end of my spring was not quite made properly or had been malformed at some point, and the one side of the spring wasn't "flat" - if I tried to stand the spring up, it would have worked on one side but the other side would have been more like the Leaning Tower of Pisa ;) I believe that "tilt" of the spring edge was causing much of the spring noise I had been hearing, since it wouldn't surprise me if the very end of the spring was being twisted around by the pressure of the washer which would cause it to spin in place rather than simply doing it's job of providing tension for the center piece and not moving, allowing the washers to spin AGAINST it. (I hope this makes sense to someone)

I tried to bend the bottom of the spring as best I could to adjust how it was positioned, and when I put everything back together and lubed it all up again I didn't have any noise coming from the springs anymore. I think I may need to file some of the extra flashing off the plastic on my cubies a bit, but that's another topic entirely ;)

Anyway I hope that helps someone. If anyone finds something similar or needs me to clarify anything just let me know.

I'm going to try this later, my DIY has a noisy side.
 
my storebought rubik's cube is making some noisy sound... and that face that is making noisy sound is hard to turn... i not yet lubricate it..
 
Ummm How do i do that?

Everyone is saying to take apart the Rubik's cube and fix the screw and spring for they don't touch or something!:confused:
But I'm a beginner and don't know how to do that!!!:(
Can someone PLEASE tell me how to fix it in DETAIL because i HATE the sound when i solve it!!!!!!!!!!!
 
Everyone is saying to take apart the Rubik's cube and fix the screw and spring for they don't touch or something!:confused:
But I'm a beginner and don't know how to do that!!!:(
Can someone PLEASE tell me how to fix it in DETAIL because i HATE the sound when i solve it!!!!!!!!!!!

do you have a diy? because if you have a storebought cube you cant take it apart unless you never want to solve it again. if you have a storebought, all i can say is lube it. theres not much else you can do to stop the noise
 
Back
Top