Making a cube core out of things around the house?

DAoliHVAR

Regular
Joined
May 28, 2013
Messages
161
is it possible?
i've tried with many different things,and most are hard to drill into.
have any of you built one
i have like 2 cubes that are coreless
 
Things around the house?

A computer to order a number of them with ;)

Other than that.. block of wood.

Milliput (well yeah I have that laying around).
 
Is your drill bit sharp? Can you sharpen it and also drill slow? Can you anchor what your trying to drill in a vice with some rag to keep it steady?

Best materials:

chunk of brass, bronze, or copper

Hardwood. Not pine, not poplar.

Carefully melted nylon?

Some other chunk of hard plastic

Not so good materials:

Marble or soapstone.

Chunk of steel cut with the right tools -cobalt or abrasive. This is how you know your an epic hard head when you see a chunk of steel and say "I can cut that down to what I need". It's also wretchedly expensive to have cobalt tooling or burn up the abrasives you would need.

Probably easier to take the change in the couch and buy one but don't let that stop your DIY sprit.
 
Last edited:
i built one out of a corner piece of a cube
dont think it will stand for long though,since it isn't very well screwed into.i dont have access to many power tools
 
Is your drill bit sharp? Can you sharpen it and drill slow?

Best materials:

Hardwood. Not pine, not poplar.

Carefully melted nylon?

Some other chunk of hard plastic

Marble or soapstone.

chunk of brass, bronze, or copper

Chunk of steel cut with the right tools -cobalt or abrasive? This is how you know your an epic hard head when you see a chunk of steel and say "I can cut that down to what I need".

Probably easier to take the change in the couch and buy one.
shipping would be too much for me lol
 
If that is really the case PM me your address and I will ship you a guhong core. On me.
aww thank you very much for the offer man,much respect for people like you.
but i have to decline.My pride won't let someone else waste their money on me.plus i made a nice core out of an edge piece recently,and it works great.
i didn't make this thread to seem like someone who is poor or anything.
but again,thank you VERY much for the offer,you are a nice person and i hope you get nice things in life :)
 
aww thank you very much for the offer man,much respect for people like you.
but i have to decline.My pride won't let someone else waste their money on me.plus i made a nice core out of an edge piece recently,and it works great.
i didn't make this thread to seem like someone who is poor or anything.
but again,thank you VERY much for the offer,you are a nice person and i hope you get nice things in life :)
How did you manage to do that?
 
How did you manage to do that?
well i would post pictures,or even a guide,but when i press manage attachments,it doesn't open :/
but basically this is how i did it:
i have a cube that the mechanism of looks sort of like a more rounded rubik's cube.
i took the edge,and broke off the part that moves in the cube.this gave me an edge piece with a big hole.
in the hole i but molten plastic,and almost completely filled up the edge piece.
the edge piece then was soft for about 1-3 minutes,which gave me enough time to drill holes in it with a tooth pick(srs)
thats pretty much it
the cap would fall off but the molten plastic makes it so that it can't.
its also much easier to do this with a corner piece,but i didn't have any
 
I have had the core in my box of extra pieces. I haven't needed it and probably won't need it. Instead of letting it get old in a box on my shelf I was just going to put it in an envelope and drop it off at the post office. I wasn't going to spend much money. Other people in the past have done far nicer things for me.
 
Back
Top