Ninja Storm
Master
Yes, that's true. But that's not what I'm doing obviously. So were you agreeing with me when I said it comes to personal preference? Because it sounded like you didn't like something I said...
Yeah, I was agreeing with you
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Yes, that's true. But that's not what I'm doing obviously. So were you agreeing with me when I said it comes to personal preference? Because it sounded like you didn't like something I said...
Yeah, I was agreeing with you![]()
3mm of space is a lot, actually. That's more than I have in mine and it is still quite fast. I usually tension (most) cubes with less than 1mm of space between the centers and core (when center is pulled). Some cubes require looser than this because of the design, but try it with the weilong. Just tighten it until its slow enough.I've tightened to the point where there's at most 3 millimeters of space in between the pieces. And the lube is really thick. The weight five is like liquid hot glue.
I really wasn't sure where to ask this, so I suppose the best place is here. Would some people be willing to watch a short video if I were to make one where I demonstrate my Weilong, the way it sounds, the way it feels, demonstrate some algorithms and 1 or 2 example solves? I am distressed that people claim their Weilongs are incredibly fast and smooth, whereas mine feels only moderately fast and smooth. I think either my tensions are off, or more likely, I've overlubed it? I tried wiping some off, but the pieces aren't even wet to begin with. This cube has yet to be my favorite one, always coming in close second. With it's popularity and supposedly "perfectness", I think it can be that for me as well. For example, my Fangshi feels nearly twice as fast as my Weilong, and I don't think that is normal.
Bottom line, I would appreciate other people's input if you are willing, but do not wish to make a 3-5 minute video if no one is willing. Thank you in advance!
I really wasn't sure where to ask this, so I suppose the best place is here. Would some people be willing to watch a short video if I were to make one where I demonstrate my Weilong, the way it sounds, the way it feels, demonstrate some algorithms and 1 or 2 example solves? I am distressed that people claim their Weilongs are incredibly fast and smooth, whereas mine feels only moderately fast and smooth. I think either my tensions are off, or more likely, I've overlubed it? I tried wiping some off, but the pieces aren't even wet to begin with. This cube has yet to be my favorite one, always coming in close second. With it's popularity and supposedly "perfectness", I think it can be that for me as well. For example, my Fangshi feels nearly twice as fast as my Weilong, and I don't think that is normal.
Bottom line, I would appreciate other people's input if you are willing, but do not wish to make a 3-5 minute video if no one is willing. Thank you in advance!
Just use a zhanchi untill youre fast enough for the Weilong
Right, but I like the Weilong better. No pops! (I HATE pops)
None of this information may be relevant to you and I'm not sure if you even are requesting help for a problem, buuuuuuut...
I have two of them. One of them (my main for about a month and a half) is well tensioned, cuts corners at almost any angle from any side (there are some impossible angles, but it's wayy more than 45 degrees) and reverse cuts well. It's impressively better than my other one. It's super smooth (smoothest I've ever owned) and extremely quiet. Except fro the few days right after being lubed, it isn't, however, as fast as my other one. In fact, I haven't cleaned it in a while and it's slower than my unlubed Zhanchi. Weilong's can vary greatly in speed depending on the amount of care you give it. Generally, the gummier ones are slower.
My other one, which is silver, is blazingly fast (comparable to the Gans III or CX3) and I decided not to lube it. On even the best tensions, however, it cuts a MAX of 45 on all sides, sometimes less than that, and in some good cases, a little bit more. The reverse cutting isn't as good, either.
I lube with semi-dry silicone lubcricant, it's bike lube called "White Lightning: Epic Ride (Semi-dry)" and I get it from wal-mart. Most people, (who are probably smarter) use either a dry or wet (or wax?) Silicone lube from the local Lowes or something. So I'm probably weird. It's amazingly fast and very wet at first, and as time passes it acutally slows the cube down to below it's unlubed speed.
Either way, with my fast silver or decent black Weilong, I find it extremely controllable. An unlubed FS is, in my opinion, either faster or less controllable (or both). I find that my unlubed CX3 and Gans III are both faster by great leaps and strides than my Weilongs.
I just use the Weilong becuase I'm so used to it, my hands are well suited for it. I get the best times on a Zhanchi or a Weilong, even though I recently switched to using a CX3 as my main.
Again, I don't know if you can glean any useful information from that!![]()
None of this information may be relevant to you and I'm not sure if you even are requesting help for a problem, buuuuuuut...
I have two of them. One of them (my main for about a month and a half) is well tensioned, cuts corners at almost any angle from any side (there are some impossible angles, but it's wayy more than 45 degrees) and reverse cuts well. It's impressively better than my other one.
Line-to-line is about 37° and I think the case you describe is 45°. I can get almost any good cube to cut 45°. It's all about lubrication and tensioning. My SuLong cuts at the other line-to-line, which is about 53°.
To clarify, here is how I see it:
![]()
// Per.
that line to line picture looks like its more than line to line.
In what universe? Here is another picture that might be clearer:
![]()
I rounded the pieces a bit much in the pictures, but the angle when the lines intersect is arctan(2) - arctan(1/2) which is about 36.8698976 degrees.
// Per.
Not really for me. I guess it depends on how you cut.Your line to lines are switched.