Type C, Lube and Screw Predicament.

IamWEB

Legend
Joined
Nov 22, 2008
Messages
2,853
Location
Right Here
WCA ID
2009BOAR01
YouTube
Visit Channel
Yes, I said 'lube and screw.'

I got my first DIY, An Old Type A, and used for a long time.

Around 8 months later, the opportunity to get 2 Rubik's.com DIYs (one white, one black) at a good price came along and I got them. My solutions to the center cap problems they are notorious for were not too good, and long story short, the red cap on the white diy was superglued to the core of the cube.

That, along with several other cube breaks (2x2 and 4x4) led to a break from practicing.

Fastforward nearly 2 months and you're here, when I get new cubes. 2 of those are the Type C and the Type F-II ordered from C4Y. During assembly of the Type C, I read online that silicone, jig-a-loo and similar lubricants will harm the screws in them because they are made of plastic. Basically I was shocked (-----> :eek:), and didn't know what to do.

What should I do so that I can lube my cube without possible damage?

I just recently, as in moments ago, finally got that center cap free on my white Rubik's.com DIY. Should I be happy and make it into a good speedcube (it's awesome!), or because I haven't needed it at all to just use it's screws to replace the Type C's?

I'm not taking the screws from my Old Type A, it's off limits, nor the F-II, it's a brand new cube.

Maybe because I'm planning to use my black Rubik's DIY cubies on the Type C frame (Erik style), I can just take them from the Rubik's DIY? This would mean that I couldn't try the Type C cubies on the Rubik's DIY frame, but I MIGHT not mind that.

Maybe I should just order some screws, springs and washers and wait?

Sorry for the long read, but basically, what do you think I should do and why?

For Type C owners, what did you do (if anything) to handle this screw situation?
 
Last edited:
Yes, I said 'lube and screw.'

its better than that: you've got a lube and screw predicament ;)

anyway your saying that lube will damage the screws because the screws are made of plastic? and the cube you have been lubing all this time isnt plastic?
 
Are you saying that the C screws are made of plastic ? Mine from C4Y are 100% metal.
And to Panyan, the lube somewhat decades the plastic, making it melt.
 
I've never heard of lube harming the screws of a Type C in any way before. Where did you get that information? I've lubed my Type C with CRC and it's been a year now..the screws still seem fine.
 
Plastic screws wat.

Every single type C I've assembled has had metal screws. But Im sure you can tell metal from plastic.

I think you should order new screws, so that none of your cubes are damaged.
 
No, no, no. There is nothing preventing you from lubing your type C. The screws are metal, and the washers are metal now too.
 
Over time, the friction between the spring and the centre turned my plastic washers into dust, so that when I went to change the spring and screw, I found a half plastic washer tangled in the spring.

I thought it was so cool.
 
Over time, the friction between the spring and the centre turned my plastic washers into dust, so that when I went to change the spring and screw, I found a half plastic washer tangled in the spring.

I thought it was so cool.
O_o

They aren't even plastic anymore though.

Ok so then later on today I'll probably just lube it then! :D
I heard you knew your stuff about Type Cs so if you say they being made with plastic then I should believe you... right? :p
 
Ok so then later on today I'll probably just lube it then! :D
I heard you knew your stuff about Type Cs so if you say they being made with plastic then I should believe you... right? :p

Yeah, I'd like to think I know my stuff about type Cs. I'd recommend that you take out an edge, spray some CRC in, and then work it in while holding a blow-dryer to the cube (not too close). It helps the lube dry out and get distributed.
 
Go ahead and post results, because in my experience, new Type Cs, after lubing, don't change that much for a while. Once they get old though, they stay slick for about a week and then go back to normal.
 
Back
Top