Timing Equipment - New Ideas

More images for the new QJ timers: apparently they don't have their own displays, as they show their timer with a Speed Stacks StackPod.

http://www.qjtoys.com/cn/Product_View.asp?ID=861
http://www.qjtoys.com/cn/Product_View.asp?ID=862

8024.JPG

%E9%BB%91%E8%89%B2%E4%B8%89%E4%BB%A3OK.jpg
 
Last edited:
My thought as per the design itself:
Similar shape to speedstacks timer
Display on timer will be width of middle section (6 digits to time up to 59:59.99)
Underneath the main display will be a display for inspection time
To the left of that will be a button to start inspection (will trigger countdown and make a "beep")
To the right of the inspection display will be the speaker (will beep at start of inspection, 8s, 12s, 15s (beep twice), 17s (beep thrice), and end of solve)
On the front of the timer will be the power and reset buttons, to avoid accidentally resetting the timer
On the right of the timer will be the data port

Minimum requirements for the timer (IMO)
data port
accurate to 0.01
no gaps
power and reset buttons out of accidental "reach"
starts on release, stops on touch (both on 2 hands)
 
Underneath the main display will be a display for inspection time
To the left of that will be a button to start inspection (will trigger countdown and make a "beep")
To the right of the inspection display will be the speaker (will beep at start of inspection, 8s, 12s, 15s (beep twice), 17s (beep thrice), and end of solve)

Ahem...

We could do things like having the timer measure the inspection time, and other such fancy things. This thread is not about that.
 
I always felt we should have the capability to plug into any common tablet display and use it as our display device. Jeremy and a few others have tried this with limited results, but I think it could be done.

Others:
- The Gen 1 design is very nice. Maybe slightly more "obvious" pads so BLD people KNOW they're hitting the pad. The reset button on the side is a brilliant idea.
- Accuracy to 0.01 seconds (preferably 0.001 seconds).
- Autoshutoff at 1 hour, if possible.
- Jeremy had another idea where we could hook up smartphones to the timers and submit times that way. Don't know how far he got on this.
- Timer should be able to take some abuse. If timer is separate from mat, timer should attach more securely to mat (more like Gen 2, not like Pro). On the older timers, the sensor will go off if you hover your hand a centimeter or two above the pad. This is not okay.
- I would prefer not to have a countdown in the timer (or if it is built in, have the ability to turn it off). Some people start before 15 seconds are up.
-
 
As Stefan pointed out, the live scoring with a tool like open cube ware should be a priority 'accessory' as well, as a compatible display, which is obviously the first thing after the timer itself. There are cubing communities around the world and not all of them have an easy access for speedstacks equipment besides the timers, so the opportunity to build them locally, as showcased by Thailand cubers some time ago, must be something to consider. Of course not everyone is in position to build one from scratch, but as chances are there might be someone with knowledge in electronic, with a set of guidelines and design standard there would be no trouble for compatible displays..
 
Last edited by a moderator:
Locally, 7-segment displays that big cost $5 each, so the digits alone would be approximately $25.

A few weeks in my spam folder and a few more emails back and forth and I was finally told how much these cost:
http://www.arkled.net/product/23-inch-single-digit-numeric-display.html

They have several versions, when you buy 1000 they cost:
SM4123011E ultra red USD0.825/PC expensive but we recommend because of best quality and intensity.
SM4123011N ultra red USD0.587/PC small-LED-CHIP inside, its intensity is only one third of SM4123011E, and its stability and reliability is not as good as that of SM4123011E too.
SM4123011E ultra yellow USD0.812/PC expensive but we recommend because of best quality and intensity.

No idea what quality your local ones are or what SpeedStacks uses, but I assume they're not better than the above good ones, so that would be about $4 for the five digits.
 
Last edited:
A few weeks in my spam folder and a few more emails back and forth and I was finally told how much these cost:
http://www.arkled.net/product/23-inch-single-digit-numeric-display.html

They have several versions, when you buy 1000 they cost:


No idea what quality your local ones are or what SpeedStacks uses, but I assume they're not better than the above good ones, so that would be about $4 for the five digits.

Yeah they likely ordered much less than 1000, and marked it up quite a bit (it's a fairly small store).
 
Yeah, would be normal. And I don't really care, what I'm interested in is the cheap high number price, since if we ever get "our own" displays, we'll surely easily want that many or more. Also, while huge competitions benefit from very large displays, for many smaller competitions probably a smaller display would suffice, lowering the price further.
 
A few weeks in my spam folder and a few more emails back and forth and I was finally told how much these cost:
http://www.arkled.net/product/23-inch-single-digit-numeric-display.html

They have several versions, when you buy 1000 they cost:
SM4123011E ultra red USD0.825/PC expensive but we recommend because of best quality and intensity.
SM4123011N ultra red USD0.587/PC small-LED-CHIP inside, its intensity is only one third of SM4123011E, and its stability and reliability is not as good as that of SM4123011E too.
SM4123011E ultra yellow USD0.812/PC expensive but we recommend because of best quality and intensity.

No idea what quality your local ones are or what SpeedStacks uses, but I assume they're not better than the above good ones, so that would be about $4 for the five digits.

What about the smaller digits at the back of the timer? That may add, say $2 to the price. Another $4 for the casing and you've got a $10 display.

I'm also designing a possible design on Google Sketchup, I'll get that finished and up ASAP.

EDIT: Wouldn't two of the digits need a second dot, so we could get a colon for minutes? Should be the 2nd and 4th digits I think.
EDIT 2: No, 2 would just have to be upside down.

EDIT 3: Couldn't we just use QJ Gen3 timers? (Obviously, there would need to be tests etc.)

That's a lot of edits...
 
Last edited:
That is interesting. I think though for the people without SketchUp they cant really see it. Possibly export some 2d images?
 
So...it's a knockoff SpeedStacks timer?

You could say that... but if you make something simular to something already made, but with different functions, it will always be called a knockoff.

I've just finished the display, so I'll update the Sketchup file and add more pictures.
 
Back
Top