# [Review]The best 1x1?

#### Cuber987

##### Member
That's about my time for two handed. How are you that fast with oh? You have any 1x1 oh algs I can use?
Use x z2 instead of x y y' z2

(100th reply!)

#### NmeCuber

##### Member
Use x z2 instead of x y y' z2

(100th reply!)
Oh ok thanks that will save a lot of time

#### Isaiah Scott

##### Member
The Best 1x1 is clearly the V Cube 1 with springs from a Gan 12. It took a lot longer than i thought to figure that out.

#### Fukuoka Kengo James

##### Member
The Best 1x1 is clearly the V Cube 1 with springs from a Gan 12. It took a lot longer than i thought to figure that out.
The GAN 120 M Pro is maglev

#### Cuber Score

##### Member
Use x z2 instead of x y y' z2

(100th reply!)
That takes too much time. I do: x' x
It should reduce your time by .334343849348 seconds, down to 2948938492384 minutes.

#### Garf

##### Member
I've been prototyping a new 1x1. I plan on naming it the T1. It has adjustable magnets, maglev, corner-core magnets, repelling magnets in the edges, magnets for the centers-edges, and a mix between UV and Matte coating. And the cube will weigh only 35 grams!

#### NmeCuber

##### Member
I've been prototyping a new 1x1. I plan on naming it the T1. It has adjustable magnets, maglev, corner-core magnets, repelling magnets in the edges, magnets for the centers-edges, and a mix between UV and Matte coating. And the cube will weigh only 35 grams!
You should add center-core magnets so that the centers don't fall out when you smash your 1x1 against the wall because it's so hard

#### Futurechamp77

##### Member
Wow. Can I pre-order?

#### Fukuoka Kengo James

##### Member
I need a week to finish it. Then I will be able to show the prototype to the world.
How much do you think is it harder to make compared to the teraminx?

#### Garf

##### Member
How much do you think is it harder to make compared to the teraminx?
Uh, not that hard. I need to add some stuff, then have the cube go through some breaking-in tests, then I'll be able to present the first prototype of the puzzle.

#### a_cuber04

##### Member
Get the GAN UV coated 1x1
But it would probably be $50, and that's being conservative with it being a Gan cube. #### lucazdoescubingstuff ##### Member But it would probably be$50, and that's being conservative with it being a Gan cube.
the GAN 110 RS is the new GAN budget 1x1, costing around 15 dollars. But if you wanna get serious, get the MAX 110 M MAGLEV PRO by TC. Or the Cosmic 120 M Maglev if you dont like OH. But if you don't like GAN, get the Moyu RS1M 2023, which costs 5 dollars.

#### Fukuoka Kengo James

##### Member
the GAN 110 RS is the new GAN budget 1x1, costing around 15 dollars. But if you wanna get serious, get the MAX 110 M MAGLEV PRO by TC. Or the Cosmic 120 M Maglev if you dont like OH. But if you don't like GAN, get the Moyu RS1M 2023, which costs 5 dollars.
the Moyu RS1M 2023 is good for multiblind as it is decent and cheap

#### TheSpeedSkewber

##### Member
Eh i dont like this one. It only has 360 degree cormer cutting

#### Fukuoka Kengo James

##### Member
Eh i dont like this one. It only has 360 degree cormer cutting
I found it similar to the bell v1 that it has better reverse than normal corner cutting

#### Cuber987

##### Member
Yo 1Bld so hard, yo, can't even get an unofficial solve yo.
My closest one yet was an X Y' Z Y' X2 Z' Y X Y' X Y' Z Y' X Z' Y X' Y X Y' Z Y' X2 Z' Y X Y X Y' Z Y' X2 Z' Y X Y away from solved

#### Cuber.Hello.com(:

##### Member
I solved the 1x1 blind in 16 moves.

Similar threads