No Hardware Twisty Puzzle?

Basic Matrix

Member
Joined
Jul 2, 2016
Messages
4
Hi I'm Vince, I (kinda) design puzzles, and right now I am designing a huge Rubik's cube, it is a 30cm x 30cm x 30cm, and I'd like to ask for help, as you can see, this cube is too big to use a screw and spring kind of hardware, so this is the problem I am currently in. I'd like to ask for help, If anyone could tell me ways to design a twisty puzzle without the need for screws and springs, this would be a great help.
 
Last edited:
Screws come in all shapes and sizes, as do springs, so I guess I'm not understanding what the problem is there, but I imagine if it really is impossible you could design a flange on the core with a matching flange on the center piece so that the center pieces snap on to the core. A similar solution is something I saw on a piece of farm equipment once, which is to have a hole through the center stem and a groove around the inside of the center piece, so that you put a beveled pin through the core and the ends of the pin slide in the groove. Both of these ideas have the disadvantage of being difficult to put together or take apart. I think your best bet is to go to your local hardware store and go through their screw and spring bins.
 
Another option might be to make round center caps, so instead of the centers spinning the pieces have torpedoes and spin around the stationary centers.
 
You can make it like a void cube and then adds centers
How does a void cube work?

Cant you buy long screws? And I hope it is a typo where you tell you are a huge rubiks cube:)
Lol, I edited it, also where can you buy ones.

Screws come in all shapes and sizes, as do springs, so I guess I'm not understanding what the problem is there, but I imagine if it really is impossible you could design a flange on the core with a matching flange on the center piece so that the center pieces snap on to the core. A similar solution is something I saw on a piece of farm equipment once, which is to have a hole through the center stem and a groove around the inside of the center piece, so that you put a beveled pin through the core and the ends of the pin slide in the groove. Both of these ideas have the disadvantage of being difficult to put together or take apart. I think your best bet is to go to your local hardware store and go through their screw and spring bins.
Thank you for the suggestions.

Maybe just make 6 Giant screws. Not having springs doesn't mean a puzzle can't function.


Edit: What about bolts?
How does it work without springs? Also, I don't know how to work with bolts.

Another option might be to make round center caps, so instead of the centers spinning the pieces have torpedoes and spin around the stationary centers.
Can you make an illustration?
 
Last edited by a moderator:
Can you make an illustration?

I'm not really a puzzle designer, nor am I any good at drawing things, so I'll try explaining it better. It might not even work, and I'm almost certain it wouldn't be a good speedcube design.

If you make a center cap in the shape of a mushroom, and then imagine the inner mechanism in the shape of a shallow bowl (split up into pieces, obviously), the rim of which fits under the lip of the mushroom. The idea is that right now the standard Rubik's cube design puts tension on the center piece pulling out from the center, whereas the tension in this design would be pulling perpendicular to that, outwards on the lip of the center piece. Corner pieces would have to hang on the edges, I think, which would be what are actually hanging on the center cap. It would be much more prone to popping, I think, and tolerances would have to be smaller, limiting corner cutting severely, but I think it should be easier to scale.

I don't know how to work with bolts.

Bolts are just big screws. You would probably need to figure out how to set nuts in the core to thread the bolts into, but that's a lot less complicated than the rest of the project.
 
I'm not really a puzzle designer, nor am I any good at drawing things, so I'll try explaining it better. It might not even work, and I'm almost certain it wouldn't be a good speedcube design.

If you make a center cap in the shape of a mushroom, and then imagine the inner mechanism in the shape of a shallow bowl (split up into pieces, obviously), the rim of which fits under the lip of the mushroom. The idea is that right now the standard Rubik's cube design puts tension on the center piece pulling out from the center, whereas the tension in this design would be pulling perpendicular to that, outwards on the lip of the center piece. Corner pieces would have to hang on the edges, I think, which would be what are actually hanging on the center cap. It would be much more prone to popping, I think, and tolerances would have to be smaller, limiting corner cutting severely, but I think it should be easier to scale.

I'm still not getting your idea. Maybe explaining it kinda simpler? I still have no progress on the hardware :(
 
Hi Vince,

if you haven't tried it yet, I would recommend to ask also at http://twistypuzzles.com/forum/.

Tony Fisher (member on both forums) might help a lot - maybe he has a describing video for his similarly large cube, as he is having for his 1.56x1.56x1.56 m (or something like this) cube.

As far as I know, building and modding is being more discussed on twistypuzzles.com rather than by speedcubers.
 
I'm still not getting your idea. Maybe explaining it kinda simpler? I still have no progress on the hardware :(

If you look at a normal speedcube, the side of the edge piece locks under the center piece, and the base of the corner fits under a flange on the edge. I'm suggesting that instead of pulling up on the center piece, the edge piece pulls out on the center, and the center does not rotate. Is that any better? I'm not sure how better to describe it.
 
Back
Top