How to make a LanLan 2x2 not suck

Such accurate measurements! I'm sure the process was extremely scientific, and is undoubtedly representative of every ES there is, not just the bad (probably) one that you own. Please tell me more!

PLEASE think before you make another claim like that

So your opinion is representative of every LL there is, not just the bad one(s) you own?

Judging from videos, my brother's one, etc. my ES is about average. Same with the LL. Funnily enough, I thought quite a lot while posting that reply.

The 98% was to account for the fact that although I'm pretty sure it's about the same, but may not be as good. As I haven't lubed it yet, I can't be sure.

The 150% was simply by measurement. I cut a corner on the ES, and then on the LL, and checked the distances. My LL was about a quarter turn loosened.

PLEASE think before you make such assumptions as that
 
Last edited:
My sample size is about 15ish Lanlans, all of which felt basically identical.

And pooling from a sample of over 100 ESs, I would agree that the average ES feels pretty crappy. Most people are too lazy to break them in properly. I'm sure the average LL feels better than the average ES to the average solver (lolsentence). But I was not speaking in comparison to the average ES. There is a lot of variance with ESs, a lot are nice and a lot are (somehow) way worse than they are out of the box. It really depends on who it belongs to. I have noticed only minor differences in LanLans, which I think can be attributed to tension.

It is impossible to tell what a cube feels like based on videos (unless it is clearly horrible), so I will leave your sample size at two.

Therefore, it is unreasonable to state that based upon your sample size of two cubes, that LanLan works 98% as well as eastsheen, etc. You could have said "My lanlan feels just about as fast as my ES, but definitely cuts corners better. Same with my brother's cubes" and you would have been unarguably correct.

It's also worth mentioning that turnspeed and corner cutting are not the only two factors in determining whether a cube is good or bad.
 
How about using springs from small cheap cubes, let's say mini DianSheng/Maru/C, possibly sanding the spring ends a bit? That would give you springs with proper ends and it would be easier to reproduce than "random ballpoint pen spring, cut off about this much".
 
My lanlan doesn't suck...I got like 0.5 seconds off my average (5.8 -> 5.3)

I may try this, anyway...

will it help with the "pops"? Or is that just me being too clumsy?

5.8 -> 5.3 isn't that much of a change, especially for 2x2.

Yeah, I suck at 2x2 anyway. And maybe my eastsheen is not good and/or properly broken in.

But it was like this:

receive cube, open box, do a couple algs, think "hmm...feels kinda good"
then do an avg of 100, which is 5.3x (previous best was 5.8x), and a 4.66 avg12 (previous best was 5.0x).

So maybe I was lucky, but I like my Lanlan better than my eastsheen. I may try the mod, since I have 2 (one still unopened).
 
How about using springs from small cheap cubes, let's say mini DianSheng/Maru/C, possibly sanding the spring ends a bit? That would give you springs with proper ends and it would be easier to reproduce than "random ballpoint pen spring, cut off about this much".

after not being too satisfied with my original spring choice, I tried some mini DS springs and they seemed to work great.
 
Though I have no idea what you could've done to make it not turn at all.

Perhaps he popped it? That's about all I can think of that would make it lock up like that. He said he played with the tension, so maybe it was super loose, he cubed with it, popped it, somehow popped it back in and then tightened it.
 
the lanlan's looklike the Eastsheen modded with core and spring. it can cut corner as well, I think I should have one
 
It's also worth mentioning that turnspeed and corner cutting are not the only two factors in determining whether a cube is good or bad.

Go on...

You serious? Pops and lockups are the other factors, that should be glaringly obvious. One could argue creaminess vs clickyness as a factor, but that is much more personal.

How about using springs from small cheap cubes, let's say mini DianSheng/Maru/C, possibly sanding the spring ends a bit? That would give you springs with proper ends and it would be easier to reproduce than "random ballpoint pen spring, cut off about this much".

after not being too satisfied with my original spring choice, I tried some mini DS springs and they seemed to work great.

I did try some other springs first, like old type A and c4y. I didn't think of miniDS springs because I totally forgot that I owned one :o Looking at them now though, they look/feel like they would work fine.

Though I have no idea what you could've done to make it not turn at all.

Perhaps he popped it? That's about all I can think of that would make it lock up like that. He said he played with the tension, so maybe it was super loose, he cubed with it, popped it, somehow popped it back in and then tightened it.

That's what I thought at first too, but when it pops you can still turn two of the axes. Unless thats what he meant by "not turn at all."
 
Hi, my white LL come with the springs like this:

o6y9at.jpg


The bigger end of the spring come in the head of the screw. Is this proper configuration? i guess not by all other cubes i have. Anyone have spring`s backwards?
 
Hi, my white LL come with the springs like this:

(picture)

The bigger end of the spring come in the head of the screw. Is this proper configuration? i guess not by all other cubes i have. Anyone have spring`s backwards?
Mine also came like this.

Edits: Just tried this on my lan lan. Please with the results, I like how this feels. :o
 
Last edited:
Zoh... mah... gawd!

I did the mod! Can we call this the "screw-spring Lanlan"? After seeing this, I kinda feel like the first one didn't count.

And you're right, it's like mine, but better.
 
I just used the same springs that it came with. Used some wire cutters to cut the 'fat' end off, about 1-coil down, so that about 4-coils remained. I then pressed a narrow screwdriver between the coils to stretch the springs back to the original length. This basically weakens the springs so they don't pull as hard. I also added some small type-A washers on the plastic end. Probably doesn't affect smoothness that much but I guess might help prevent wear.

The mod works a treat - one satisfied customer :D

Cheers for the tip Mr Woner.
 
David. Woner. You. Are. A. Genius!!!
This mod is great! I'm making a video on it.
Great job, Dave!

At first I was like "Oh no." cause it felt like it does when one of the sweeper things inside is about to come out. But it hasn't yet!

Again, great idea, and I think everyone should try it.
 
Yeap, the performance of the cube improves a lot, no doubt. I used mini DS springs according to previous tips. I wonder if something similar can be done with the stiff Maru 2x2?

So basically, the springs suck and almost any modifications to it (cutting, swapping) makes it better?
 
Uh, I think I messed up my LL somehow while trying this. I can push in a screw without having to screw it in, on one side of the core (this works with any of the LL screws). And when I do screw it in, it doesn't stay in; it pops out after I try to put in an edge or two. =\
Picture%2010.jpg
 
Back
Top