Dayan 4x4 wth

I also got a x-cube 4 a few weeks ago, it sucked at first, but after a couple of solves it got better, although i dont think it has reached its maximal potential, the inner layers are still pretty clicky but outer layers are great.
radmin: how long did it take for u to break in a x-cube to awesomeness?
 
I got around to taking mine apart yesterday evening.

I've tried to colour code the comments for clarity.

Edges

First thing I had noticed was the fact that the edges weren't flush, which looks pretty ugly on a white cube. The gaps were pretty big on some pieces so I took the edges apart and found three areas with excess sprue that was hindering the bits from fitting properly.

img0144dz.jpg

By b4p4076 at 2011-05-19

This stuff falls out when you separate the pieces, it is also still stuck along the highlighted area. Just scrape it off with a box cutter.

There is excess plastic build up around these pins, it's mostly the pin that I've highlighted here, but it can also be others on some edges. Box cutter.

Sometimes there's also excess plastic around the holes that the pins go in to that you might need to remove.

Core

img0143c.jpg

By b4p4076 at 2011-05-19

Needed to shave the the excess plastic sticking out from around the holes on the core. Not that important but my core was pretty bad in that aspect.

Washers

img0140rl.jpg

By b4p4076 at 2011-05-19

Old washers
DaYan 4 washer
Carnage

When I dismantled the core I was shocked. Loads of ground up plastic everywhere.
Although I didn't take a picture, one of the washers had actually gotten stuck on the screw which in turn, was holding the spring under pressure. Lots of plastic shavings/ powder stuck in the springs too. It took some force to separate them. First thing I did was to swap the washers for ones left over from my DY4. The one on the far left of the photo was even bent/ faulty :(

So yeah, cleaned it all out.

Lube

Lubed the following parts:

Under the screw head
On the bottom of the spring
Under the washer
In the core centers
The core pieces in general

I had already lubed the outer parts.

Conclusion

You'll laugh, but the inner layers run smoother and with less force than the outer ones. It's a proper speed cube now. Now I just need to become a proper 4x4x4 speedcuber ;)

Anybody know a mod for the outer layers? I mean, they don't have to be as fast as those on the X-Cube or anything. Maybe just as easy to turn as the inner layers...
 
Last edited:
thanks for the "review" or what to call it, it sounds really weird that your inner layers turns better than the outer, for me its the opposite.
Did you watch izowired assembly tutorial? because before he assembled the cube he actually scraped off some of the excess plastic.

I didn't bother to scrape it off tho, which resulted in a crappy cube for a week, but im actually thinking of disassembling it to remove those scraps actually
 
The inner layers on my ShengShou 4x4x4 are easier to turn than the outer layers too, so it's not unusual on a 4x4x4 ;) On the X-Cube it's the other way around for example.

Did you take your core apart like I did? Lubing the springs and washers and such could make a difference. And I suspect those crappy washers were slowing things down considerably. They were literally digging into the plastic.

Thanks for the tip, I'll go look for that vid this evening then ;)
 
Cool. Let me know how it went :)
I just hope the new washers and the lube will prevent my cube's core centers from deteriorating even more, otherwise this cube won't be getting very old...
 
I'm not sure if I've posted on this already or not, but what I did to mine, which has worked for everyone I've told to do this, is to take it completely apart to get to the 2x2 core, and LUBE INSIDE THE 2x2 structure. You just pop an edge out of the 2x2 core and put some lube inside. Then, TENSION the 3 main screws on the CORE. You want to loosen them enough so that the core will not pop, but will turn well. Then, screw the ball shells back onto the core and tighten them ALL THE WAY. This will keep your outer layers sturdy and stable, while your inners are fast and smooth due to lubing and tensioning the core.
 
I'm not sure if I've posted on this already or not, but what I did to mine, which has worked for everyone I've told to do this, is to take it completely apart to get to the 2x2 core, and LUBE INSIDE THE 2x2 structure. You just pop an edge out of the 2x2 core and put some lube inside. Then, TENSION the 3 main screws on the CORE. You want to loosen them enough so that the core will not pop, but will turn well. Then, screw the ball shells back onto the core and tighten them ALL THE WAY. This will keep your outer layers sturdy and stable, while your inners are fast and smooth due to lubing and tensioning the core.

Yeah did more or less the same. but took everything apart, lubed the screws/ springs and swapped the washers for wider ones too.

Big fan of your YouTube stuff btw. !

Regards,

H.
 
I did the same thing, just took it apart etc. But after a while it got slow, and my edges just flew out of the cube, even though it wasnt very loose, so i switched to my x-cube, gonna disassemble it right now

brb with results.
 
turned out great! although it still pops from time to time...

i just realised i would do so much more 4x4 if there was a perfect cube..

Sweet! My DaYan 4x4x4 is sexy as hell after the dis/reassembly stuff.

As perfect as what? As an excellent 3x3x3? Because even those aren't "perfect". But I get your flow...

Have fun with your "new" cube btw. :)
 
heh, I mean, a cube that doesnt pop or stuff, i'm streaming some cubing atm if ur interested
http://j-tv.me/lMUVw0

I know bruv ;)

Thanks for asking me over man :) Will be right there, needs to learn stuff...

Not Found

The requested URL /forum/47 was not found on this server.

Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.
Apache/2.2.16 (Unix) mod_ssl/2.2.16 OpenSSL/0.9.8e-fips-rhel5 DAV/2 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 PHP/5.2.9 Server at www.speedsolving.com Port 80

Thanks for nothing :(
 
Back
Top