Moyu DianMa cube

I hope that this isn't just another one of YJ's scheme to make money like the Sulong or the Chilong
 
Cuberulz10 said:
I may not get much quicker, but is this cube got good cutting? My Zhnchi cannot even cut 1 cubie, after tensioning it a 100 times and it pops like MAD.
Click to expand...

Try tensioning your zhanchi this way then.

 
Last edited by a moderator:
Rocky0701 said:
If Soren333's video doesn't work, i recommend a Weilong, it will almost NEVER pop even with really loose tensions, but it still has as good of corner cutting as a Zhanchi and way faster turning.
Click to expand...

Unless you don't do extreme corner cutting, then it will never pop. I've had the problem with corner twists every 20 solves or so.
 
I assume you are talking about the Weilong. I have only had it for about a week, probably done 300 solves but i haven't had a pop at all, i have even tried to pop it, and i think i literally would break the cube before i could pop it, so i stopped. I have pretty tight tensions, but i can't take an edge out at all. I have to loosen a side to take the cube apart.
 
Rocky0701 said:
I assume you are talking about the Weilong. I have only had it for about a week, probably done 300 solves but i haven't had a pop at all, i have even tried to pop it, and i think i literally would break the cube before i could pop it, so i stopped. I have pretty tight tensions, but i can't take an edge out at all. I have to loosen a side to take the cube apart.
Click to expand...

I guess even though we have the same cube, each cube on their own are inherently different. Or perhaps it's probably because we tensioned and lubed it differently. I lubed the core the usual way, and lubed the pieces just a tiny bit. And mine is on medium tensions imo.
 
I highly doubt its the cubes fault, I will admit that there are always duds but the zhanchi is a really good cube. Instead of getting a new cube adjust your turning style. Try practicing on a really lubed rubiks brand that will get your turning really precise
 
thanks for your advice. Yet, I really hate my DaYan Zhanchi. I disassembled it, cleaned all pieces ( even spring&washer) used Crazybad's tutorial to re-assemble it and now it is terrible. Can't cut 1 cubie, I used Cyoubx's tutorial and even camcuber's but it just failed. not only that, it pops 1/2 of my solves. I really need a new cube. I'm going for a fangshi v2 'coz its cheap at cubezz, and (i think) a WeiLong is too fast for me. 31.01 sec avg.

Anyway, any review on the DianMa? Looks really great. Check out my mechanism pics i posted earlier.
 
Soren333 said:
Try tensioning your zhanchi this way then.

Click to expand...
Umm... That is the tutorial i used. it always failed, maybe 1 side could do 45, the rest were bad. My cube was a dud, i think. Thanks anyway
 
Last edited by a moderator:
You must log in or register to reply here.

Similar threads

Thomas.Caleb
MoYu WCA World Championship 2027
2
Replies
21
Views
772
Fukuoka Kengo James
Fukuoka Kengo James
Michael Wimberly
Vin3 Nova, MoYu RS3 M V5, and MGC Square-1 V2 Review
Replies
5
Views
298
Michael Wimberly
Michael Wimberly
A
MoYu cube comparison
Replies
1
Views
298
Michael Wimberly
Michael Wimberly
I
  • Poll Poll
Moyu weilong v11 review
Replies
0
Views
1,176
Isaac Webb
I
Michael Wimberly
  • Poll Poll
Best cube brand other than GAN or MoYu
Replies
15
Views
966
LukeKing67
LukeKing67
Back
Top