Dayan 6: PanShi [pictures]

You've gotta change up the winning formula completely every now and then to get a better one, otherwise we'd be stuck at better-looking Model T's lol
I have to say, perhaps FangShi and the ShuangRen signals the end of the reign of Dayan, but I kinda hope not
 
My panshi came today
Diy kit came without half of an edge piece and 3 broken corner stem parts
The torps had strips of plastic sticking out of them and some of the centres look like they have been grinding. But from the 2 sides that don't fall apart each turn (missing pieces) it turns about the same as a zhanchi ( hard to tell though only moving two sides)

If this is dayans attemp at a new cube... They have failed

What am I meant todo with a unusable cube
 
Does anyone know how many screw threads are exposed at 'ideal' tensions? At first I thread the screws in until all threads were in the core and this made it impossible to assemble so I backed it out till about a pennies worth or threads were exposed. After assembly I rotated all 6 screws 90 degrees. I'm not sure what other people are running for tensions so I thought I'd ask.

What I did for tensions: I assembled the cube, then loosened each side one by one until the top part of the screw (the permanent washer thing) lines up with the top of the cylindrical screw hole if that makes sense. I test this by running my fingernail back and forth over the screw and the centre piece screw hole until my fingernail runs smoothly over the two without jumping or dropping. I then tighten the screw in with 25 90degree turns with torpedoes in or 24 90degree turns without torpedoes. This tension provides optimal corner cutting for me and cuts at pretty much almost any angle though there is a certain spot where a little more pressure is needed to be used to cut.
 
What I did for tensions: I assembled the cube, then loosened each side one by one until the top part of the screw (the permanent washer thing) lines up with the top of the cylindrical screw hole if that makes sense. I test this by running my fingernail back and forth over the screw and the centre piece screw hole until my fingernail runs smoothly over the two without jumping or dropping. I then tighten the screw in with 25 90degree turns with torpedoes in or 24 90degree turns without torpedoes. This tension provides optimal corner cutting for me and cuts at pretty much almost any angle though there is a certain spot where a little more pressure is needed to be used to cut.

Just what I wanted. Thanks!
 
I recieved mine the other day. I got the DIY version, assembled and lubricated it. I am not too impressed (with and without torpedos). But I do believe that doing a simple mod may help the clunkiness feel. Has anyone tried sandind down the base of the corner stock and the contact point the edge? I think even though this is a super simple mod it may work. Has anyone tried this before? Has anyone had a different successful mod?
 
Yes, I mean 6 full rotations and a quarter of a full rotation, that's with torpedoes in the cube. Without torpedoes, then just 6 full rotations.

Thanks for confirming. The reason I am surprised because when I initially put the centers on the core, they were crazy loose but I think it was around the point that the screws were flush with the center cylinder and I think I only did about 2 full rotations after assembling. Is your cube pretty tight?
 
Thanks for confirming. The reason I am surprised because when I initially put the centers on the core, they were crazy loose but I think it was around the point that the screws were flush with the center cylinder and I think I only did about 2 full rotations after assembling. Is your cube pretty tight?

Yes, my cube is pretty tight, but I tension with the intention of getting good corner cutting. I expect all Dayan cubes to cut 45, so I always try to get 45 and if possible, even more. My Panshi can cut from pretty much every angle, a teeny spot where a bit more force is needed to cut though. My tensions give me enough reliability, control and speed. If anyone tries my tensioning technique, please give me feedback on how it performs.
 
So you get better corner cutting with tighter tensions? I've always experience the opposite. Anyway, my experience is the Panshi is too lock-y with tighter tensions.
 
Back
Top