Improve your Lunhui through correct assembly

  • Thread starter Thread starter Deleted member 12389
  • Start date Start date
D

Deleted member 12389

Guest
I was trying to break in my 2nd lunhui. It turned like it was grinding on a bumpy road -unlike my first lunhui which turns smoothly.

Under bright light, I noticed that there were tiny gaps where the assembled pieces meet. I had not exerted enough pressure to close them tight.

Once I tightened these gaps (now they look like a 'lines', rather than 'gaps'), the turning improves significantly and the lock ups disappear.

Hope this helps someone with similar problems (with lunhui or other dayan cubes)

Apology for the title - can't think of another one.
 
Do the Guhongs have this?

I got a Lubix Ultimate about 2+ months ago, and there is a gap on all the corner and edge pieces. It's not a line, but an actual gap. Should it be a line on the Guhong? There has been an accumulation of dirt inside, and it's filled up with gunk. I could either take a pin and scrape it off, or take it all apart, clean, and put it back together.

Since Lubix assembled it, I just believed that it's how they are supposed to be...

I don't see any problems with my solving, though. No real lock-ups, and turning is very smooth. Maybe I don't notice, because the gap has filled up with gunk...?

Anyone else have something similar with their Guhongs? Especially from Lubix?
 
A Guhong is like that. They don't have a gap only if you're lucky. When they come out from the mold, the plastic pieces flex and bend a little which means, you cannot modify it to remove the gap. From my experience; All Guhong DIY kits have at LEAST 1 corner with a noticeable gap and at least 2 corners with gaps that are noticeable only if you inspect the cube very closely. The Lunhui corner pieces don't flex because they have that triangle (the thing you insert into another piece to make the corner piece) to reinforce it. The GuHong's corner piece doesn't have anyreinforcement because you connect them using a separate tri-wing piece.
 
Do the Guhongs have this?

If you're talking about gaps on the faces of the edges and corners where those two touch, then those are normal. But if you're talking about gaps on the outward facing seams of the pieces, Lubix doesn't fix that factory issue on assembly apparently. You can easily fix it yourself though.

Corners
You just need to file down the "star" pieces that go into the corners slightly to fix the gap problem on those. There'll always be a fine gap on the faces of the corners that point inwards though. The LingYun has that too btw.

Edges
You can fix the edges by scraping away any unwanted plastic around the pins and holes and any surplus sprue in general.

Both are pretty quick fixes ;)
 
Last edited:
I don't mean dirt as in actual dirt from the outside ground. I should've used another word.
I meant, just as in crap that has been slowly collecting in there, and has formed actual gunk in the gaps.



If you're talking about gaps on the faces of the edges and corners where those two touch, then those are normal. But if you're talking about gaps on the outward facing seams of the pieces, Lubix doesn't fix that factory issue on assembly apparently. You can easily fix it yourself though.

If you turn a face 45degrees, and look at the inside of the edge pieces where stickers don't go, the line where the pieces meet when assembled, I have small gaps there.
It sounds like we're talking about the same area, so it's a good thing that it's normal. I'll just scrape off the gunk, like someone also said.

Thanks.
 
I did historically see a post about the gaps specifically on GuHongs with the triangular pegs. It mentioned rotating the triangular peg so each of the three pegs is then inserted into a different corner. I also remember seeing Donovan from Lubix state it did work when he tried it so it may be worth a go. Not much use on a Lingyun or Lunhei granted!
 
Back
Top