Inside a Stackmat

I suggest looking at the stackmat pictures in Stefan's first post. In the second picture, the bottom left hand corner has the headphone jack. Notice how if you look at the first picture, in the bottom right (where the headphone jack is now) you see three wires? That's for left, right, and common/ground/neutral (whatever you prefer to call it). My guess is that the middle solder point is the common.

What do you mean by you got the timer to turn on?

I meant that I got it to show that the timer was "on" on cct timer program. I'll try to post some pictures up, I have to fix my camera. I was looking at stefan's pictures, and I think that there are some parts on the new timers that aren't on the old one.

Hmm while this thread is here, I'd like to ask about a problem with my stackmat:

The time and date is still displayed, and when I hit the power button the 0.00 comes out. But when I put my hands on the timer the display it goes 8:88.88 very briefly then goes off. Is it out of battery or something? I don't have a new battery that I can test it with =/

You just need a new battery. :)

Ok, so with some more testing today I should figure this out. I think that the timer I have is missing some parts that are on the new timer. I have got my hands on two 3.5 mm jacks (one with a resistor on it, one without) and I think that I might actually be able to figure this out with some help from my uncle (very smart with electronics). Hope everything works out, and maybe if my uncle can fix my camera, i'll post up pictures on how my timer looks. If I figure it out i'll post it up here and I'll make a video tutorial. Cheers :)

I guess he got CCT to react but it probably needs tuning (input volume and program settings) to work properly.

Where it says R27, R is for resistance, mabye you also need that resistor to get it to work...

Do you know what size resistor I would need for what ever R27 is? also there is something to the right of it that reads DINA and has two soldering points with the sign for an amplifier on it (sideways triangle with horizontal line on either end). So i'm guessing that this "amplifier" spot is for the sound wave that is sent through the wire to the computer? What kind of "amplifier" would that be?

My stackmat won't turn on, and I tried to disassemble it, and when talking off the back plate, was met with ribbion looking things holding the halves together. What do I do? (Or how do I get my stackmat to work? It's Not the batteries. I checked)

You might have a bad switch. Carefully open the timer, you don't want to damage the ribbon. Also, make sure that the wires to the battery are all completely connected to the battery place and the circuit board. cheers
 
Last edited by a moderator:
UPDATE: Ok, so I figured out where to connect the two wires from a headphone jack to make the timer work, now I just need to figure out how to attach and actual jack to the timer so I don't have to have a wire hanging off my timer. With the help of my awesome uncle, I found that I need to attach one of the wires to ground and the other one to the right square where it says R27. So just one more step to go, i'll have to continue next week because I won't see my uncle until then. Cheers :)
 
That "sideways triangle with a line" is for diode, not amplifier. Since the jack is stereo, you would probably need to connect all three wires to something. Notice how the jack in Stefan's pictures have all three points soldered in, but on the solder points you can't see them leading to any traces, so I'm guessing they lead somewhere else on the front side. I didn't see an R27 anywhere close to the jack though, but I might have missed it. It would probably be easier to look at it in person.
 
That "sideways triangle with a line" is for diode, not amplifier. Since the jack is stereo, you would probably need to connect all three wires to something. Notice how the jack in Stefan's pictures have all three points soldered in, but on the solder points you can't see them leading to any traces, so I'm guessing they lead somewhere else on the front side. I didn't see an R27 anywhere close to the jack though, but I might have missed it. It would probably be easier to look at it in person.

Yeah, I am going to test it later on during the week and will post an update, and hopefully a tutorial if it actually works.
 
So, you put the wire where the resistor is supposed to be and it does not work else?

The resistor is a lead but with resistance, if it is missing there is no lead there at all so this is why it works that way, you take a shortcut by putting the wire at that place.

R27, the number 27 is just the numbering for the resistors of this particular card and it does not say anything about the size of the resistor, you have to look at one on a a card that has got it and I can't see it on Stefans pictures. Probably it is only on the special revision of the card that lacks the display jack.
 
Last edited:
So, you put the wire where the resistor is supposed to be and it does not work else?

The resistor is a lead but with resistance, if it is missing there is no lead there at all so this is why it works that way, you take a shortcut by putting the wire at that place.

R27, the number 27 is just the numbering for the resistors of this particular card and it does not say anything about the size of the resistor, you have to look at one on a a card that has got it and I can't see it on Stefans pictures. Probably it is only on the special revision of the card that lacks the display jack.

So, if I want to put a port on the circuit board, I have to put a certain sized resistor on it as well? I am going to go see my uncle this saturday and sunday, so I will let you know if we figure out anything else. If it works I will post exactly how I did it, and a link to a video tutorial. Thanks for helping. Cheers!
 
I'm not sure you need the resistor, it may just be a small value like a few K or so, it may work fine without it.

Oh, ok. That is good to know. Just a couple more days and I can continue testing, can't wait! Cheers!
 
OK, the new battery did nothing to help the stackmat. I tried both types of battery. CRxxx and the Dxxx. (I have no idea the real name) Both didn't work.

When you disassembled it, or if you are going to do it again. Make sure that your battery is connected properly and that none of the wires are broken, crimped, or disconnected from the circuit board or the connections that the battery actually touches. Also look to see if there are any parts that look burned or damaged in any way, water in the system can cause a short. Lastly make sure that you are getting power to the on/off switch on both ends of the switch. If you are only getting power to the on/off switch, but not on the other side when the switch is turned on, then your power switch is bad. Chances are your on/off switch is bad considering it was working for months after water got in it. I would try replacing the on/off switch and the reset switch it should only cost you a couple bucks. If that isn't the problem then something is probably shorted out.
 
A lot of times people use resistors in line with microphones, so since this is broadcasting a signal, maybe that's why the resistor is there. Although I'm not sure, since you'd think that should be on the version with the jack, not the version without.

Were you ever able to give us pictures? It would be good to have both stackmat versions to compare/contrast.
 
When you disassembled it, or if you are going to do it again. Make sure that your battery is connected properly and that none of the wires are broken, crimped, or disconnected from the circuit board or the connections that the battery actually touches. Also look to see if there are any parts that look burned or damaged in any way, water in the system can cause a short. Lastly make sure that you are getting power to the on/off switch on both ends of the switch. If you are only getting power to the on/off switch, but not on the other side when the switch is turned on, then your power switch is bad. Chances are your on/off switch is bad considering it was working for months after water got in it. I would try replacing the on/off switch and the reset switch it should only cost you a couple bucks. If that isn't the problem then something is probably shorted out.

I'll try that. Im going to have to look up half of what you just said though. Im so electronically challanged.
 
A lot of times people use resistors in line with microphones, so since this is broadcasting a signal, maybe that's why the resistor is there. Although I'm not sure, since you'd think that should be on the version with the jack, not the version without.

Were you ever able to give us pictures? It would be good to have both stackmat versions to compare/contrast.

I will be able to post some pictures tomorrow. Cheers!
 
I'll try that. Im going to have to look up half of what you just said though. Im so electronically challanged.
Haha, it ok. You'll know if anything is burned or damaged, if it is that means its shorted out, or too much heat is pushed through the component causing it to get burned and die. The switches are just the buttons that are under the on/off button and reset button. You can test them with a voltmeter. Hope this helped, if you have any other question, please ask, I am happy to help. Cheers! :)
 
So my brother was leaving to college today, so I was not able to go to my uncle's house and finish the timer. Sadly we will have to wait another week. I will try some of my own tests on the timer while I wait. If I get it right I will make a video. Cheers!
 
Ok, now i'm just angry. It's snowing over here right now and I really hope it stops. I was really looking forward to getting my timer finished tomorrow, hopefully i'll be able to finish it tomorrow.
 
Hey everyone, great news! I just got back from my uncles house and the timer worked! I will post up some pictures below. Enjoy, cheers!
 
Hey everyone, great news! I just got back from my uncles house and the timer worked! I will post up some pictures below. Enjoy, cheers!

Ok, so after using the timer for 2 days I came across two problems.

1) While timing, after a certain amount of time my computer would randomly put down times on the side like 7.01 or 13.01.

2)yesterday when I tried to use it yesterday it didn't work.

I think I do need the resistor that was missing I just need to figure out how big or small the resistor needs to be. Any ideas?
 
Back
Top