Rubik's Wood Cube

I tried it out in New York, just before they kicked me out of the booth. It didn't turn very well.

Could you see if the internals were plastic? Did it at least turn as well as a typical store-bought? Why did they kick you out?!

Chris
 
I didn't have a chance to check the internals. It was no better than a store bought. I was afraid to be rough with it. They kicked me out because I am a was "a competitor".

It was funny. When I walked in they looked at me funny, and then called this giant guy from their staff room and had him come out and tell me to leave. As if they anticipated trouble or something. Pretty ridiculous.
 
They kicked me out because I am a was "a competitor".

At first I thought you meant speedcubing competitor (like most of their customers would be). But I guess it was your V-Cubes endorsement? Did they think you were doing recon on their new mech designs or something?
 
They kicked me out because I am a was "a competitor".

At first I thought you meant speedcubing competitor (like most of their customers would be). But I guess it was your V-Cubes endorsement? Did they think you were doing recon on their new mech designs or something?

Were you wearing your V-Cube shirt perhaps? I'm wondering if that might have been the reason.
 
Photo of mechanism

The cube has a plastic core and plastic feet on the pieces. Each foot is fastened with a small Phillips screw, which means you could use your own wood pieces. Not sure if the center caps are glued on.

This one feels tight out of the box. The wood probably has more friction. I'll break it in and see what happens. VERY heavy! Nice item in my opinion.
 

Attachments

  • woodmech.jpg
    woodmech.jpg
    54.5 KB · Views: 140
The cube has a plastic core and plastic feet on the pieces. Each foot is fastened with a small Phillips screw, which means you could use your own wood pieces. Not sure if the center caps are glued on.

This one feels tight out of the box. The wood probably has more friction. I'll break it in and see what happens. VERY heavy! Nice item in my opinion.

I plan on buying one of these next week, but I could see where these could be problematic years down the road if used heavily and the screws loosen and possible strip the wood. That said, it won't stop me from enjoying mine.

Mike

BTW, I enjoyed your vid for solving this cube... http://www.youtube.com/watch?v=QUBwSVx2S4c&feature=related
 
Last edited:
How are you supposed to lube it?

Silcon spray.

Honestly, this cube turns worse than a new store-bought. I don't see how you could cube with it. My usual time is sub 20. My time with that was sub 2 min. :o

Have you lubed yours? I couldn't really 2 either, but I lubed and it just feels like a really heavy storebought. I'm still easily sub30 on it.
 
Honestly, this cube turns worse than a new store-bought. I don't see how you could cube with it. My usual time is sub 20. My time with that was sub 2 min. :o


Needless to say, a must for the collector, needless to say I have it!!! I used paraffin-candle- for the cubies as they are wood and silicone for the center. It turns quite good after this treatment
 
I bought a couple of these bad boys, one for collector's sake (sits on the shelf and in the hex-packaging), one to play around with. I haven't gotten around to lubing it yet, which is why it's hella-tight, although it seems to get a little bit better (either it's gotten looser or I've just gotten used to it). I do prefer cubes to have a little more heft to them, although this is ridiculous.

The thing is a piece of art, though.
 
The wooden cubes are VERY hard to turn out of the box, even harder than my Studio cubes (which are the harder than any store bought I have). Corner cutting is almost non existent out of the box. It almost feels as if it did not even have springs. I will try paraffin on one and bar soap, bees wax and Slipit sliding compound on others, as I get them.

The stickers are put on very badly. They are hard, almost tile like, so the edges that stick out feel uncomfortably sharp against my fingers.
Also, the transparent yellow is very hard to see, especially in dimmer light.
I am not sure how comfortable I feel re-stickering these. I wonder if it will be possible to purchase see-through replacement stickers.
 
The wooden cubes are VERY hard to turn out of the box, even harder than my Studio cubes (which are the harder than any store bought I have). Corner cutting is almost non existent out of the box. It almost feels as if it did not even have springs. I will try paraffin on one and bar soap, bees wax and Slipit sliding compound on others, as I get them.
Silicone was fine for mine. Also I retained my other cubes for speedcubing - you should have done the same :)
The stickers are put on very badly. They are hard, almost tile like, so the edges that stick out feel uncomfortably sharp against my fingers.
Also, the transparent yellow is very hard to see, especially in dimmer light.
I am not sure how comfortable I feel re-stickering these. I wonder if it will be possible to purchase see-through replacement stickers.
I'm sure you could find some good replacement tile material with a bit of effort. Personally, I'm leaving mine in the box -- I have dozens of cubes to choose from that are actually designed for speed. It's an ornament dude!
 
I used paraffin wax on my first wood cube and only got a VERY slight improvement. It is horrible and not even good to slow solve. I ordered more in hope that I get a better one.
I got one of the center caps off (which are glued on), only to find out that there are no adjustable screws. That is really too bad, as this cube could have had much more potential. I was unable to tell if it had any springs, the core was THAT tight.
I think it is odd and a shame that the pioneer twisty cube company makes some of the worst products on the market...
 
Despite my reluctance, I went ahead and used Jig-A-Loo (have another one that sits on the shelf) and it turns significantly better, although it does have a solvent effect on the plastic guts. M2 slices are actually possible and U2 and R2 doesn't involve the entire wrist.
 
Back
Top