Bad moving, sticky cube.

LuisaoJR

Member
Joined
Nov 9, 2009
Messages
21
Hello guys, i'm kinda new to speedsolving.com
well
i have my DIY A and it was a veery good cube as most people say
i used it for like 1 week
and lubed it.. ok my avgs are now a lot better because of him ( sub 35 )
i've been using him since october 20th
bt from like 3 weeks ago it's becoming the worst cube ever.
i can' even move it correctly it's all sticky and nasty, and believe me
i tried everything
i disassembled it cleaned all of it, including screw and springs and core, took off all the silicone and etc... and now?
it's still the same
it's like if i had a bubble gum between each of the sides its really horrible to move it.
does anyone have an idea, or a suggestion to give me, on what to do ( besides getting another cube plz ;D ) with THIS cube, to make it better and usable again?

Thanks
Luis
 
Last edited:
I can think of three possibilities right now:

1. It is still a little bit wet. Cubes are usually bad when they are wet.
2. You need to lubricate it again.
3. It has worn down, but I really doubt that this is the case.
 
hmm well..
wet i'm sure it's not
i cleaned it twice... wth 2 different towels first i took of all the siicone with one little wet
and then i dry with another one
lubricate.. hmm i don't think this will help, i tried it last week.
and what u mean with worn down?
 
Adjust the tension. You have to experiment when you first get them. Try loosening it a bit.
 
already did it... if i put it too loose it pop with one move, if i put it to tensioned italmost doesn't move, the tension i'm putting it is the one that is still possible to use the cube, bat hardly!

and about the lubing
i cleaned once and relubed it to try
still the same horrible thing
then i cleaned and now its not lubed, and same still.
 
Well, I doubt that a type A would wear down. I think the only cube that wares down with normal use if type F1.

Type F plastic "degrades" over time, and then it doesn't turn very well. But, I used a type A for a long time, and it was always great.

I just thought of a few more questions for you:
1. Did you tension it properly?
2. Are you using a random lubricant, or are you using a recommended one?
3. Have you ever used a petroleum based lubricant on it?
 
i Use jimo pure silicone lubricant
never used anything else to lube it.

jimo is one of the few silicone only lubricants we can find here, most cubers in brasil use it.
and the tension is what i said above, too loose it pops too tensioned it doesn't move the tension i use is the regular
 
yeah, that's really what my cube looks like,
i htink i have adhesives glueing all the cubies.
 
i Use jimo pure silicone lubricant
never used anything else to lube it.

jimo is one of the few silicone only lubricants we can find here, most cubers in brasil use it.
and the tension is what i said above, too loose it pops too tensioned it doesn't move the tension i use is the regular

JIGALOO!!! Others=:eek: not good. Stock up on Jigaloo.
 
i Use jimo pure silicone lubricant
never used anything else to lube it.

jimo is one of the few silicone only lubricants we can find here, most cubers in brasil use it.
and the tension is what i said above, too loose it pops too tensioned it doesn't move the tension i use is the regular

JIGALOO!!! Others=:eek: not good. Stock up on Jigaloo.

Explain CRC then.
 
there is no jig a loo or crc in brazil
in brazil we have JIMO and WORKER

and they are ALL PURE SILICONE!
 
Back
Top