[Review] The best 1x1?

[Cuber987]

That's about my time for two handed. How are you that fast with oh? You have any 1x1 oh algs I can use?

Use x z2 instead of x y y' z2

(100th reply!)

 

[NmeCuber]

Use x z2 instead of x y y' z2

(100th reply!)

Oh ok thanks that will save a lot of time

 

[Isaiah Scott]

The Best 1x1 is clearly the V Cube 1 with springs from a Gan 12. It took a lot longer than i thought to figure that out.

 

[Fukuoka Kengo James]

The Best 1x1 is clearly the V Cube 1 with springs from a Gan 12. It took a lot longer than i thought to figure that out.

The GAN 120 M Pro is maglev

 

[Cuber Score]

Use x z2 instead of x y y' z2

(100th reply!)

That takes too much time. I do: x' x
It should reduce your time by .334343849348 seconds, down to 2948938492384 minutes.

 

[CatSharked]

2948938492384 minutes

2,047,873,953 days. That beats my PB by 1 day.

 

[Garf]

I've been prototyping a new 1x1. I plan on naming it the T1. It has adjustable magnets, maglev, corner-core magnets, repelling magnets in the edges, magnets for the centers-edges, and a mix between UV and Matte coating. And the cube will weigh only 35 grams!

 

[NmeCuber]

I've been prototyping a new 1x1. I plan on naming it the T1. It has adjustable magnets, maglev, corner-core magnets, repelling magnets in the edges, magnets for the centers-edges, and a mix between UV and Matte coating. And the cube will weigh only 35 grams!

You should add center-core magnets so that the centers don't fall out when you smash your 1x1 against the wall because it's so hard

 

[Futurechamp77]

Wow. Can I pre-order?

 

[Garf]

Wow. Can I pre-order?

I need a week to finish it. Then I will be able to show the prototype to the world.

 

[Fukuoka Kengo James]

I need a week to finish it. Then I will be able to show the prototype to the world.

How much do you think is it harder to make compared to the teraminx?

 

[Garf]

How much do you think is it harder to make compared to the teraminx?

Uh, not that hard. I need to add some stuff, then have the cube go through some breaking-in tests, then I'll be able to present the first prototype of the puzzle.

 

[a_cuber04]

Get the GAN UV coated 1x1

But it would probably be $50, and that's being conservative with it being a Gan cube.

 

[lucazdoescubingstuff]

But it would probably be $50, and that's being conservative with it being a Gan cube.

the GAN 110 RS is the new GAN budget 1x1, costing around 15 dollars. But if you wanna get serious, get the MAX 110 M MAGLEV PRO by TC. Or the Cosmic 120 M Maglev if you dont like OH. But if you don't like GAN, get the Moyu RS1M 2023, which costs 5 dollars.

 

[Fukuoka Kengo James]

the GAN 110 RS is the new GAN budget 1x1, costing around 15 dollars. But if you wanna get serious, get the MAX 110 M MAGLEV PRO by TC. Or the Cosmic 120 M Maglev if you dont like OH. But if you don't like GAN, get the Moyu RS1M 2023, which costs 5 dollars.

the Moyu RS1M 2023 is good for multiblind as it is decent and cheap

 

[Garf]

the Moyu RS1M 2023 is good for multiblind as it is decent and cheap

Yo 1Bld so hard, yo, can't even get an unofficial solve yo.

 

[TheSpeedSkewber]

Eh i dont like this one. It only has 360 degree cormer cutting

 

[Fukuoka Kengo James]

Eh i dont like this one. It only has 360 degree cormer cutting

I found it similar to the bell v1 that it has better reverse than normal corner cutting

 

[Cuber987]

Yo 1Bld so hard, yo, can't even get an unofficial solve yo.

My closest one yet was an X Y' Z Y' X2 Z' Y X Y' X Y' Z Y' X Z' Y X' Y X Y' Z Y' X2 Z' Y X Y X Y' Z Y' X2 Z' Y X Y away from solved

 

[Cuber.Hello.com(:]

I solved the 1x1 blind in 16 moves.