Polyurethane Glue for Magnets

Reed Merrill

Regular
Joined
May 14, 2017
Messages
111
Location
Canada
Hey everyone,

The Cubicle just released their DIY magnetization kit, and the most interesting thing I noticed was that they supply polyurethane glue with it. In their how-to youtube video Phil talks about how when the glue sets it becomes shock-proof, which seems to me like a big advantage over super glue.

Does anyone know where it can be purchased? I haven't noticed anyone talking about polyurethane glue on this forum, but I was wondering what people's experience with it has been?
 
Hey everyone,

The Cubicle just released their DIY magnetization kit, and the most interesting thing I noticed was that they supply polyurethane glue with it. In their how-to youtube video Phil talks about how when the glue sets it becomes shock-proof, which seems to me like a big advantage over super glue.

Does anyone know where it can be purchased? I haven't noticed anyone talking about polyurethane glue on this forum, but I was wondering what people's experience with it has been?
It's what the original Gorilla glue is, before they started making other types. It can be a little messy, but what glue isn't. I've used it before. You really need the helper magnet method using this glue as it isn't instantaneous like super glue. If you don't have a magnet on the exterior of the piece you're gluing to hold the newly glued-in magnet in place, you risk having it move out of place while the glue cures. This type of glue also tends to bubble (depending on humidity) and expand several times the size of drop you use, and some types need to be water activated by spritzing a little water on it. At least that's the best way to use the original formula Gorilla.
I've seen Titebond listed in a catalog I have that is also polyurethane-based, but haven't tried it. Reading online about it, it appears you don't need the water activation on it, so it might be the better one of the two brands.
 
Ah, ok. That is all good to know. Thanks! So in your experience a good super-glue job works fine and has good longevity?
 
Ah, ok. That is all good to know. Thanks! So in your experience a good super-glue job works fine and has good longevity?
I think if applied correctly, it will withstand the rigors of solving. I've made about 100 magnetic cubes and had about 4 have a magnet come loose. But I think that's possible with just about any kind adhesive.
I personally like to use Gorilla brand Impact Tough Formula superglue. It's a little thicker and more fibrous than other superglues. And it's always a good idea to apply the glue first, so it's under the magnet, then finish up with a drop that goes along the edge and top of the magnet, basically encapsulating the magnet. Also, it's always a good idea to clean the interior of the cubie pieces with rubbing alcohol at the places where the magnets will go. A lot of factory lube actually ends up inside the pieces.
I think I'll give the Titebond polyurethane glue a try. I was always under the impression that Chris Tran made his own glue mix, putting in a little acetone with the polyurethane glue, just based on a couple of things I observed. Anyway, if the Cubicle is using polyurethane glue, it's worth another look!
 
Good to know! @DMCubing, I was just wondering, would you say that acetone/nail-polish remover is also an acceptable solvent for factory lube? That's just what I have around, from my wife. :D
 
Good to know! @DMCubing, I was just wondering, would you say that acetone/nail-polish remover is also an acceptable solvent for factory lube? That's just what I have around, from my wife. :D
No, not at all. Acetone can actually dissolve ABS plastic if you're not careful with it. You sure wouldn't want to be getting it all over a cube. It's better/safer to use a solvent like rubbing alcohol to remove lubricant.
 
It's what the original Gorilla glue is, before they started making other types. It can be a little messy, but what glue isn't. I've used it before. You really need the helper magnet method using this glue as it isn't instantaneous like super glue. If you don't have a magnet on the exterior of the piece you're gluing to hold the newly glued-in magnet in place, you risk having it move out of place while the glue cures. This type of glue also tends to bubble (depending on humidity) and expand several times the size of drop you use, and some types need to be water activated by spritzing a little water on it. At least that's the best way to use the original formula Gorilla.
I've seen Titebond listed in a catalog I have that is also polyurethane-based, but haven't tried it. Reading online about it, it appears you don't need the water activation on it, so it might be the better one of the two brands.
I actually like this because you don't have to worry about the glue instantaneously hardening while the magnet gets out of place. You also can get the magnet well in the glue so it's much better in the end.
 
No, not at all. Acetone can actually dissolve ABS plastic if you're not careful with it. You sure wouldn't want to be getting it all over a cube. It's better/safer to use a solvent like rubbing alcohol to remove lubricant.
Ah, ok! Also very good to know.

I actually like this because you don't have to worry about the glue instantaneously hardening while the magnet gets out of place. You also can get the magnet well in the glue so it's much better in the end.
Now that you mention it, the easier gluing process is probably part of the reason Cubicle decided on a slow setting glue. That way fewer of their customers are likely to botch their magnetizations.
 
I actually like this because you don't have to worry about the glue instantaneously hardening while the magnet gets out of place. You also can get the magnet well in the glue so it's much better in the end.

I've always used cheap superglue, and it does give you a couple seconds to move the magnet around, and a few more to pop the magnet out if it's in the wrong place. Not a ton of time, but enough, and you don't really have to wait to reassemble the cube.
 
Back
Top