Hi Everyone,
As I has seen on youtube, someone put a type D's spring into Eastsheen's center, and it can cut corner for small degree. Now, I have improved this method, for better Eastsheen 4x4x4.
What you need?
1/ An Eastsheen 4x4x4 (of course)
2/ Mini C2
3/ The Screw/spring set of the type A, we will only need the Washers.
So, begin this mod, you will take out 4 center pieces of the Eastsheen 4x4x, take out the screw. then add the Mini C2 Spring, and the Type A's Washers upside down, so from the corner to the center cap, it will be : Washer -> Spring and the screw.
Continue applying this mod for all six sides of the Eastsheen 4x4x, then you just need to adjust the tension of the Screw to all six sides. Please note to make it tight, if it loose, the cube will be pop
And you done. Now your cube and cut corner, and it turns much better, not so loose like normal one.
Here are the pictures, sorry that I let you all wait for a long time.
What you need :
An Eastsheen 4x4x4
Mini C2 and the Washer from Type A screw/spring set (see below)
So, begin modding, you just need to put the the "smooth" side of the washer directly to the Center, then put the spring and the Eastsheen's screw on it, see pictures below :
Rough side of the Washer :
Smooth side of the Washer :
After adding this, just apply to all six sides. The important key here is to set the tension of the Screw for all 6 sides of the cube, they must have the same length to keeping all the pieces.
My camera can not record the video, so that I give you this picture as example :
I'm not sure this cube is the best 4x4x4, but in comparing with QJ, it can cut corner like QJ, and can cut corner from the second layer, which the QJ can not do this, it can only cut the outer layer. This mod has a washer, so that the spring won't contact the center, so your center will be safe.
p/s : if you find any English mistakes in this topic, please let me know, sometimes my grammar is bad.
As I has seen on youtube, someone put a type D's spring into Eastsheen's center, and it can cut corner for small degree. Now, I have improved this method, for better Eastsheen 4x4x4.
What you need?
1/ An Eastsheen 4x4x4 (of course)
2/ Mini C2
3/ The Screw/spring set of the type A, we will only need the Washers.
So, begin this mod, you will take out 4 center pieces of the Eastsheen 4x4x, take out the screw. then add the Mini C2 Spring, and the Type A's Washers upside down, so from the corner to the center cap, it will be : Washer -> Spring and the screw.
Continue applying this mod for all six sides of the Eastsheen 4x4x, then you just need to adjust the tension of the Screw to all six sides. Please note to make it tight, if it loose, the cube will be pop
And you done. Now your cube and cut corner, and it turns much better, not so loose like normal one.
Here are the pictures, sorry that I let you all wait for a long time.
What you need :
An Eastsheen 4x4x4
Mini C2 and the Washer from Type A screw/spring set (see below)
So, begin modding, you just need to put the the "smooth" side of the washer directly to the Center, then put the spring and the Eastsheen's screw on it, see pictures below :
Rough side of the Washer :
Smooth side of the Washer :
After adding this, just apply to all six sides. The important key here is to set the tension of the Screw for all 6 sides of the cube, they must have the same length to keeping all the pieces.
My camera can not record the video, so that I give you this picture as example :
I'm not sure this cube is the best 4x4x4, but in comparing with QJ, it can cut corner like QJ, and can cut corner from the second layer, which the QJ can not do this, it can only cut the outer layer. This mod has a washer, so that the spring won't contact the center, so your center will be safe.
p/s : if you find any English mistakes in this topic, please let me know, sometimes my grammar is bad.
Last edited:
