Help with DianSheng 333

Fishcake

Regular
Joined
Jan 3, 2009
Messages
29
I just bought a white DianSheng no.333 last Saturday. It's painted, has weird looking edges and corners, and the corners are pretty sharp. I lubed it with silicon spray after solving it a few times, and the cube now turns a bit faster.

I did some research about in this forum and a lot of people said that no.333 is not that good, as compared to no.222. Well, I do notice some weaknesses of the cube. Sometimes it locks when I turn too fast, and it does not cut corners very well. Moreover, it's hard to distinguish between the orange and the red. I messed up a lot of solves because of that...

So, is there any way (advice) to turn it into a better cube, or all hope is gone?

P.S: I'm new to choosing cubes and DIYs stuff. My last cube (the first one I bought) was a store bought from Toys R Us.
 
dian sheng is more suitable for beginners,not for speedsolving.
most ppl like to erase the paint and stick it...
 
Last edited:
dian sheng is more suitable for beginners,not for speedsolving.
most ppl like to erase the paint and stick it...

Really? I thought DianSheng is the China Replica DIY type E. And I see a lot of speedcubers use DianSheng in YouTube, and they have sub-20 average. I bought DianSheng after reading a cube review of type A - F in YouTube, and the person who did it recommended type E. Coincidentally, last Saturday I saw it in a shopping mall, and bought it.

I dislike paint too, but I couldn't find vinyl stickers anywhere around here. :(
 
Diansheng's are definitely not only for beginners. They can make fabulous speedcubes. I have not tried the superior 222, but I'm pretty impressed with the 333. But I must say that I've been hearing quite a bit about DS's not being consistent. They're hit or miss cubes.

As mentioned before, sticker over the point or just scratch it off.

I have tried: Types A, C, D, E (333 only), F, C4U, Rubiks.com DIY, and quite a few hybrids.
 
Diansheng's are definitely not only for beginners. But I must say that I've been hearing quite a bit about DS's not being consistent. They're hit or miss cubes.

People say that the cubies and the color of the core vary. After researching about DianSheng for a quite some time, I found out that it can come with normal cubies or the weird ones, and the core may be in red or white. I think the color of the core does not matter, but the shape of the cubies makes a lot of different. The normal ones are definitely better, so if you get it, you're lucky. Unfortunately, I got the one with the weird cubies. :(

SparkZer said:
Why not just cut your own stickers? Cubesmith sells vinyl sheets, or, you could go to oracal.com and find a distributor of oracal 751 intermediate cal vinyl in your area ( oracal 751 intermediate cal being the same type that is sold at cubesmith)

My country is not even listed in the website > < Are vinyl sheets considered as art materials? If yes, then I might be able to find it in art shops, and they're plenty of them near my campus.

Oh, I also learned about setting tension of the springs to make the cube more loose. It turns out the cube is now a bit better at cutting corners. But since I'm new to DIYs, I'm not sure if it is considered good enough. The turning speed, however, didn't change much. Plus, the cube tends to pop from time to time.
 
People say that the cubies and the color of the core vary. After researching about DianSheng for a quite some time, I found out that it can come with normal cubies or the weird ones, and the core may be in red or white. I think the color of the core does not matter, but the shape of the cubies makes a lot of different. The normal ones are definitely better, so if you get it, you're lucky. Unfortunately, I got the one with the weird cubies. :(
Precisely. The one with the weird cubies is known as Diansheng no. 333, and the one with the normal cubies is known as Diansheng no. 222.
 
Back
Top