Effect of Lube

hawkmp4

Master
Joined
May 17, 2008
Messages
1,395
So, since I just put stickers on my DIY, I had washed all the gunk off from the old stickers and just washed all the cubies with detergent to clean everything out. On a whim, I took an average of 25 of my T-perm and got 2.33s. Then, I lubed the cube, worked it in fully, and did another average of 25. I got 2.22s.
That's a...
(2.33-2.22)/2.33 * 100 = 4.7% increase in times.
Kinda showing my thoughts that lube helps the cube feel better but any increase in times is pretty insignificant, especially considering these gains only happen when you're turning at full speed, which is not your entire solve. Anyone want to try and replicate this/ refute this idea?
 
Lube can have a positive effect on a cube (Turn a slow cube into a good cube)
or have a negative effect (Melts your cubies and fuse 'em together).


On topic: I am not going to try this.
 
Lube can have a positive effect on a cube (Turn a slow cube into a good cube)
But I don't think it really does as much as people think. I think we're getting a placebo effect most of the time.

Yes, I agree! I've been saying that for a while.
This is especially true for type A and store cubes. I think the effect of lube is much more significant on type D though.
 
Well atleast for me i noticed that my old type A does not have a great improvement due to lube. I also agree with the placebo effect idea. The first time i used CRC i thought it was godly, but then after using it again on another cube i noticed that truly it didnt significantly increase its turning speed. (on 2 storebought cubes)
 
Can people do something similar, and post what type and what improvement in speed they got? I'd like to finally have an answer to this question :)
I used a type A by the way.
 
Yes, I agree! I've been saying that for a while.
This is especially true for type A and store cubes. I think the effect of lube is much more significant on type D though.

Can people do something similar, and post what type and what improvement in speed they got? I'd like to finally have an answer to this question :)
I used a type A by the way.

How about not doing this with a previously lubed cube but with one that's never been lubed before?

ok. story time. I have been using a black type A as my main cube since the end of march. I lubed around the beginning of june and did not lube it for the res tof the summer. during the summer it was subjected to some hard times: lots and lots of solving(obviously), 10 days of high heat and dust/dirt exposure at summer camp(didnt clean it afterwards), and like 150 speed-assemblies(stefan knows how rough that can be on a cube). at the end of august, i finally got my first sub-20 avg, which was 19.99. the day after that, i lubed my cube, worked it in, then went to bed. the next day I got a 18.95 average of 12. my first sub-18 also came after lubing.

i may be alone here, but i find that lubing actually helps my F2L more than my LL. LL algs can be performed just as fast on a tight cube if you have the finger strength. it makes f2l easier because the turning is so effortless that it is easy to relax. it feels like i am going slow, even though i am going fast, which makes look-ahead way better.
 
i washed my black type A with soap and water as well..i wanted to remove the silicone to break it in more because previously i lubed the cube as soon as i assembled it.
after washing it still seems smooth like there was still silicone in it..so i didnt lube it again..and i use it for OH now though my OH sucks
 
On my cubes I do an initial lube with original stickers. I work this in and probably relube after a couple days (it's been a while) and after this I wait till the stickers become useless (another week or so) then I get new stickers. I clean all faces of the cube well with alcohol. Apply stickers. Solve it for a day. Then apply more lube. Now it should be as good as its going to get without internal mods. I dont' lube it ever again. It usually keeps about the same amount of lube-y-ness untill I break something. The main slowdown I've found is just dust buildup inside my cubes. Biggers cubes seem to suffer more severely from this problem. (severely in how slow they can get, not how fast it builds up necessarily)

tl;dr - I'm just saying an initial lube is good, continuous lube doesn't do much.
 
Yes, I agree! I've been saying that for a while.
This is especially true for type A and store cubes. I think the effect of lube is much more significant on type D though.

Can people do something similar, and post what type and what improvement in speed they got? I'd like to finally have an answer to this question :)
I used a type A by the way.

How about not doing this with a previously lubed cube but with one that's never been lubed before?

ok. story time. I have been using a black type A as my main cube since the end of march. I lubed around the beginning of june and did not lube it for the res tof the summer. during the summer it was subjected to some hard times: lots and lots of solving(obviously), 10 days of high heat and dust/dirt exposure at summer camp(didnt clean it afterwards), and like 150 speed-assemblies(stefan knows how rough that can be on a cube). at the end of august, i finally got my first sub-20 avg, which was 19.99. the day after that, i lubed my cube, worked it in, then went to bed. the next day I got a 18.95 average of 12. my first sub-18 also came after lubing.
But that's throwing in wayyyyyyy more variables than just lube...
 
Back
Top