Different springs for different sides?

koreancuber

Master
Joined
Jan 31, 2010
Messages
1,089
Location
Seoul, Korea, South Korea
YouTube
Visit Channel
Ok, this is just an idea, so please don't criticize me too much. Yesterday, while I was trying on different springs for different cubes, I thought, what if I put different screws on different sides of the cube? For an example, on the U face (usually yellow, Last Layer Color) I could apply a spring set that had fast turning, decent corner cutting, and good popping resistance. Since we use the R side a lot, we could put springs that were never popping, decently fast and very accurate. These are some of the examples. So, If you wanted to put different springs on different sides of a cube, what kind of springs (and which core) would you put on the U, D, L, B, R side? (This just a question, it probably wouldn't work, but It also might). For the expert cubers: would this theory work? If not, why? (Sorry for being so demanding, but it was in my head for the whole day.) Thanks, and Happy cubing.
 
seems like it would work decently for LL, but I'd probably pop the cube during cross or f2l if the tensions weren't similar. But I am not expert, this is just my opinion.

I think if I got use to it, it would work, but it's just my thought :).

welll see... I suck at cross and f2l, so with the cube rotations, I might have a problem. Other than that I can't see why this wouldn't work.

I tried having yellow (my LL) a little looser to do algs quicker... but I'd usually get a pop on PLL
 
seems like it would work decently for LL, but I'd probably pop the cube during cross or f2l if the tensions weren't similar. But I am not expert, this is just my opinion.

I think if I got use to it, it would work, but it's just my thought :).

welll see... I suck at cross and f2l, so with the cube rotations, I might have a problem. Other than that I can't see why this wouldn't work.

I tried having yellow (my LL) a little looser to do algs quicker... but I'd usually get a pop on PLL

It would work with expert cubers that don't need a lot of cube rotations. They could just practice on two opposite sides when doing the F2L. I guess it would be hard for the beginners like me.
 
seems like it would work decently for LL, but I'd probably pop the cube during cross or f2l if the tensions weren't similar. But I am not expert, this is just my opinion.

I think if I got use to it, it would work, but it's just my thought :).

welll see... I suck at cross and f2l, so with the cube rotations, I might have a problem. Other than that I can't see why this wouldn't work.

I tried having yellow (my LL) a little looser to do algs quicker... but I'd usually get a pop on PLL

It would work with expert cubers that don't need a lot of cube rotations. They could just practice on two opposite sides when doing the F2L. I guess it would be hard for the beginners like me.

Also, I believe a lot of expert cubers at least use opposite face for cross solving, if not color neutral. So if someone used white and yellow both for possible crosses, then I don't think it would work as well.
 
Also, I believe a lot of expert cubers at least use opposite face for cross solving, if not color neutral. So if someone used white and yellow both for possible crosses, then I don't think it would work as well.

I know, but there are cubers that don't use it. Or they could use the same set of springs for the U and D.
 
It seems like a somewhat fathomable idea, you should look into it. It wouldn't be as helpful for those of us who are color neutral, though. :P
 
you can put different springs on the U and D side, but the R, F, L, and B wouldn't work very well.
also, you will need to putthe same spring on thew U face as well as the D face. when the cube is assembled there are small gaps between each center cubie and the core arm. if the spring tension is unbalanced the whole core moves towards the tighter side. this causes lock-ups because the screw is no longer at the center of the bottom hole of the centerpiece. or worse, if the screw fits perfectly in the hole it actually causes the adjascent sides to become stiffer than the spring tension should produce.


p.s: sorry about the run-ons
 
you can put different springs on the U and D side, but the R, F, L, and B wouldn't work very well.
also, you will need to putthe same spring on thew U face as well as the D face. when the cube is assembled there are small gaps between each center cubie and the core arm. if the spring tension is unbalanced the whole core moves towards the tighter side. this causes lock-ups because the screw is no longer at the center of the bottom hole of the centerpiece. or worse, if the screw fits perfectly in the hole it actually causes the adjascent sides to become stiffer than the spring tension should produce.


p.s: sorry about the run-ons
Thanks for the explanation.
i have actually tried this idea, but i think it would degrade the quality of the cube. The outcome was a rather bad cube

Ok. Thanks
 
Back
Top