Alpha 4

Alpha 4?

  • Like

    Votes: 9 50.0%
  • Dislike

    Votes: 9 50.0%

  • Total voters
    18
  • Poll closed .
attachment.php

did you mean "the big washer" are washers that made from plastic?
Can you explain the teory behind the picture?
i dont really get the point from the picture about making the cube faster..:confused:

anyway, i like the A4
it does lock up, but it's not that bad. it cuts corner quite good too tho, and I think it's the cheapest from all Guo Jia Alpha 3x3x3 series (exlude the minis)

gosh, do you still not get it, having seen such a obvious diagram?

the plastic washer have the same outer radius as the big washer, and the inner radius is larger than the springs'. this means that with the same gap setting, the one with plastic washers will have more room for the spring than the one without, hence less normal force applied upon the cubies.

this is kinda similar to removing the small washer or cutting the springs, as it compresses the spring less under the same gap setting. but since removing the small washer causes the center piece to wear out, this would be the best way to make your cube pop less.
 
Last edited:

did you mean "the big washer" are washers that made from plastic?
Can you explain the teory behind the picture?
i dont really get the point from the picture about making the cube faster..:confused:

anyway, i like the A4
it does lock up, but it's not that bad. it cuts corner quite good too tho, and I think it's the cheapest from all Guo Jia Alpha 3x3x3 series (exlude the minis)

gosh, do you still not get it, having seen such a obvious diagram?

the plastic washer have the same outer radius as the big washer, and the inner radius is larger than the springs'. this means that with the same gap setting, the one with plastic washers will have more room for the spring than the one without, hence less normal force applied upon the cubies.

this is kinda similar to removing the small washer or cutting the springs, as it compresses the spring less under the same gap setting. but since removing the small washer causes the center piece to wear out, this would be the best way to make your cube pop less.

:eek: wow, I didnt relize that...
Thanks, that makes sense. I'll give it a try. :D

each set get 2x6 big plastic washers.
should they be use 2pcs in a center pieces?

what about the small plastic washers?Can they be used as well?
 
Last edited:
i prefer my cube to be more springy, so i wouldn't put any of the stopper-washer on. but because those who just started learning finger tricks may they needs to have their cube tighter o prevent pops, this is a good way to have the cube tight without making the cube very stiff.
normally you'd add one plastic stopper if you want you cube faster and less springy. you wouldn' put two even if your turning technique is horrible.

PS: this cube is already a completely unpoppable cube even without the plastic stoppers
 
Just did the memory mod, and I have to tell you, it's better than the A-2 and A-3f. I find the A-2 a bit unstable because of it's popping rates even though it's at a medium-tight tension. The A-3f is all good, but I can't seem to go really fast on it. And for the A-4, I used a knife to round all the corners (I did them carelessly) and it turned out great. I'm not going to mention anything about the corner cutting and the popping resistance, because this cube can cut 45 degrees even at a tight tension and it does not pop. The got a bit faster, so I had to tighten it a bit, which was good because it reduced the lockups on the cube. The m slices feel a bit crisp (?).

So, if you have an A-4 and you hate it, I really recommend trying the memory mod. (oh, by the way, this is my secondary speedcube.)
 
Last edited:
Back
Top