All of my rage. (QJ 4x4 mini failure)

goatseforever

Regular
Joined
Aug 5, 2009
Messages
150
Location
CA
YouTube
Visit Channel
So I got my QJ Mini 4x4 in the mail today, and as I was solving the ****er for the 5th or 6th time, it exploded. I put the thing back together, two turns later it explodes again. So I'm putting it back together again and then it occurs to me that one of the shells on the core isn't, like, attached to the core. I know I didn't explain that very well, so here's a picture:
12510175.jpg


Now, I'm no expert on the 4x4 or it's mechanism, so I'm not sure if that thing is meant to be detachable and I'm just putting it together incorrectly or if I should superglue that piece back on. That piece is shaped differently than all the other ones in that the corners are like concave instead of pointy. Does anyone with a mini QJ know?

UPDATE: Gave it a chance, got some super glue and glued the core back. 2 solves later it exploded again; this time a different piece broke off. Sent it back to Amazon, ordered a Maru. The end.
 
Last edited:
isnt the concave bit so that you can fit the centre pieces in easier...?
 
i dont know where all the horror stories of qj and mini qj come from. i have done at least 20,000 solves on my full sized one, 20,000 on a mefferts, and about 20,000 on a mini qj and none of mine have snapped. the cores are still in tact as well as the center pieces (which seems to be the other complaint). my mefferts now overshoots, my mini qj overshoots, and my full size qj (i kept it unlubed since i've owned it) turns slower, but it doesnt overshoot at all.
 
I snapped a center right at the stalk. Yeah. Getting that replaced. Previous owner neglected to inform me of that damage :P looks like there was superglue there previously....
 
Superglue works fine in corner pieces but the center ones tend to snap often since they receive too much stress. I have yet to break the core, but I'm working on it.

The horror stories are true.
 
i dont know where all the horror stories of qj and mini qj come from. i have done at least 20,000 solves on my full sized one, 20,000 on a mefferts, and about 20,000 on a mini qj and none of mine have snapped. the cores are still in tact as well as the center pieces (which seems to be the other complaint). my mefferts now overshoots, my mini qj overshoots, and my full size qj (i kept it unlubed since i've owned it) turns slower, but it doesnt overshoot at all.

If you average 1 minute per cube, it would take 48 hours of practice a WEEK for an entire year to do 60,000 solves. Your number is obviously very, very far off.
 
i dont know where all the horror stories of qj and mini qj come from. i have done at least 20,000 solves on my full sized one, 20,000 on a mefferts, and about 20,000 on a mini qj and none of mine have snapped. the cores are still in tact as well as the center pieces (which seems to be the other complaint). my mefferts now overshoots, my mini qj overshoots, and my full size qj (i kept it unlubed since i've owned it) turns slower, but it doesnt overshoot at all.

Really? You have done 60,000 4x4 solves. Yea right, even if you get times of 45sec for all of the those 4x4 solves. 60,000 solves * 45 seconds= 2,700,000 seconds / 60= 45,000 minutes / 60= 750 hours / 24= 31.25 days.

There is no way you been solving your 4x4 for 31.25 days. This doesnt factor in scrambles and inspection or variation of the time it took you to solves. So there is no way you have solved a 4x4 60,000 times.:fp
 
Is it the lube those at factory put in? plastic destroyer type?

When I disassembled my mini QJ for cleaning this lube, it had some dust big enough for not to be regular cube dust.
 
Back
Top