3x3 ShengShou Aurora?

rj, if it pops, then you're doing it wrong or it isn't tensioned well enough. This cube performs well at loose and tight tensions, but it tends to pop at looser tensions. At tighter tensions, out of 1000 solves, I only got 2 pops, and I'm a rough turner. So torpedoes are not needed if you tension it right... There is a little hole there in the edge pieces for some reason, and I thought maybe it was for torpedoes, but apparently not. Besides, gluing pieces on the internal mechanism is a bad idea, it messes with the symmetry of the design.
All in all, I find this to be an amazing cube. It's a good step up from your basic "entry level" speedcube, bridging the gap between slow cubes and cubes like the Moyu Weilong and the Dayan Zhanchi. Definitely a good main speedcube, especially for those averaging between 20 and 40 seconds. I don't know about faster times, but I can attest to perfect performance in that range. Etiher way, I still prefer faster cubes, even if this one is an amazing cube.

It has a veryyy smooth feel. Like creamy butter. It's gorgeous, I think. The pieces can stretch very far even on the tightest tension, looking like it should just fall apart. It's extremely controllable. The tracks are good, but causes lubing to be a problem, as it actually tends to increase friction. So I lube it VERY sparaingly.

It's made of cheap plastic and comes with amazing stickers. The plastic is bad enough that when somebody once dropped it on concrete (he's never touching my cubes again.), it had a dent/abrasion mark. I would get a black one, in that case. Though it is beautiful in either color. The stickers it comes with are just superb and slightly brighter than you'd expect from other ShengShou cubes.

The corner cutting is phenominal and can be good at multiple tensions. Reverse corner cutting varies from core to core, and from face/side to face/side. It's not absolute and you might not get the same results as I did. My white SS Aurora's green side can corner cut about 55 degrees and reverse corner cut nearly an entire cubie, or about 37.5 degrees. The white side, however, can only corner cut 44 and reverse cut about half a cubie with a fair amount of effort. Any further, and it simply locks. It'll pop if you try to unlock it. If it locks, trust it. It means it simpluy cannot do what you're asking of it. It doesn't need it, though. Cutting is completely effortless all the way up to 40 degrees. It feels a bit smaller than your average cube because of the embezzeled cubies and smoothened exterior. The mech is simple and effective, without added complications or features. It's easy to mod (48 PEM and 24 CPM should be applied by any serious cuber. makes this cube even smoother.) and fun to just solve! Slowly solving is so smooth it made me giggle for the first few DOZEN solves. It's hilariously nice to turn.
It's also dead silent unless you're going for insane TPS. It makes no noise whatsoever for the accurate turner.
Besides the above mentioned flaws and the fact that you can very easily twist the corners, even on tight tensions (but I've NEVER actually had a corner twist during a real, fast, agressive solve. I've solved it hundreds of times), his cube is a very high quality cube.

I recommend it for newbs and veterans alike. Good for efficient methods and the M slices on this baby flow like no other cube can attest to. It even corner cuts M slices.

Those are my thoughts on the SS Aurora, which was my main until I switched to the Moyu Weilong :)
 
rj, if it pops, then you're doing it wrong or it isn't tensioned well enough. This cube performs well at loose and tight tensions, but it tends to pop at looser tensions. At tighter tensions, out of 1000 solves, I only got 2 pops, and I'm a rough turner. So torpedoes are not needed if you tension it right... There is a little hole there in the edge pieces for some reason, and I thought maybe it was for torpedoes, but apparently not. Besides, gluing pieces on the internal mechanism is a bad idea, it messes with the symmetry of the design.
All in all, I find this to be an amazing cube. It's a good step up from your basic "entry level" speedcube, bridging the gap between slow cubes and cubes like the Moyu Weilong and the Dayan Zhanchi. Definitely a good main speedcube, especially for those averaging between 20 and 40 seconds. I don't know about faster times, but I can attest to perfect performance in that range. Etiher way, I still prefer faster cubes, even if this one is an amazing cube.

It has a veryyy smooth feel. Like creamy butter. It's gorgeous, I think. The pieces can stretch very far even on the tightest tension, looking like it should just fall apart. It's extremely controllable. The tracks are good, but causes lubing to be a problem, as it actually tends to increase friction. So I lube it VERY sparaingly.

It's made of cheap plastic and comes with amazing stickers. The plastic is bad enough that when somebody once dropped it on concrete (he's never touching my cubes again.), it had a dent/abrasion mark. I would get a black one, in that case. Though it is beautiful in either color. The stickers it comes with are just superb and slightly brighter than you'd expect from other ShengShou cubes.

The corner cutting is phenominal and can be good at multiple tensions. Reverse corner cutting varies from core to core, and from face/side to face/side. It's not absolute and you might not get the same results as I did. My white SS Aurora's green side can corner cut about 55 degrees and reverse corner cut nearly an entire cubie, or about 37.5 degrees. The white side, however, can only corner cut 44 and reverse cut about half a cubie with a fair amount of effort. Any further, and it simply locks. It'll pop if you try to unlock it. If it locks, trust it. It means it simpluy cannot do what you're asking of it. It doesn't need it, though. Cutting is completely effortless all the way up to 40 degrees. It feels a bit smaller than your average cube because of the embezzeled cubies and smoothened exterior. The mech is simple and effective, without added complications or features. It's easy to mod (48 PEM and 24 CPM should be applied by any serious cuber. makes this cube even smoother.) and fun to just solve! Slowly solving is so smooth it made me giggle for the first few DOZEN solves. It's hilariously nice to turn.
It's also dead silent unless you're going for insane TPS. It makes no noise whatsoever for the accurate turner.
Besides the above mentioned flaws and the fact that you can very easily twist the corners, even on tight tensions (but I've NEVER actually had a corner twist during a real, fast, agressive solve. I've solved it hundreds of times), his cube is a very high quality cube.

I recommend it for newbs and veterans alike. Good for efficient methods and the M slices on this baby flow like no other cube can attest to. It even corner cuts M slices.

Those are my thoughts on the SS Aurora, which was my main until I switched to the Moyu Weilong :)

Dude, I was wondering if it was possible. No need for a lengthy answer. I use the same cube as you do, and I'm considering experimenting with torps in a Aurora. I'm also considering getting a Aurora at all. Thanks for the full review :D.
 
Dude, I was wondering if it was possible. No need for a lengthy answer. I use the same cube as you do, and I'm considering experimenting with torps in a Aurora. I'm also considering getting a Aurora at all. Thanks for the full review :D.

That dude reminds me of someone i work with that sends 4 page emails to a simple yes or no question.
Hey, he answered the torpedo question in a few lines. The rest might be helpful information for someone else. This is the Aurora thread after all... not OAQT.
 
He didn't answer it. I was asking if it was possible.

Like Lchu613 said... anything is possible. Dapianokid just went further by saying that it was a bad idea and that you don't need torpedoes if you have the cube set at the proper tensions. I don't really think you were just asking if it was "possible". That's like me saying I don't like my cube because it is too uncontrollable fast and asking if I can put some honey in the core, then expecting someone to say "yes" and leave it at that. I'm just making a point. So I think there's an implied "Yes, but..." in front of whatever Dapianokid said in his reply.
 
Ok. I would like to add an anti pop mech. Any ideas?

Unless there's another kind of mech I don't know about, "anti pop mech" = "torpedo". If you really really wanted to add torpedoes, you could either glue them in or screw them in (like a Guhong v1 with screw torpedoes I've seen in some videos). But you will risk making the cube worse or destroying it in the process. The risk is up to you. You could also try taking torpedoes out of another cube and putting them in the Aurora (may require some modding on the torpedo piece). The safest is to first try tensioning it (as Dapianokid mentioned) so it doesn't pop so much because if you don't like the tensions you can always go back and adjust it.
 
Unless there's another kind of mech I don't know about, "anti pop mech" = "torpedo". If you really really wanted to add torpedoes, you could either glue them in or screw them in (like a Guhong v1 with screw torpedoes I've seen in some videos). But you will risk making the cube worse or destroying it in the process. The risk is up to you. You could also try taking torpedoes out of another cube and putting them in the Aurora (may require some modding on the torpedo piece). The safest is to first try tensioning it (as Dapianokid mentioned) so it doesn't pop so much because if you don't like the tensions you can always go back and adjust it.

Screw torpedoes? Link please!
 
I've found that putting in a few drop of maru lube in my aurora makes it insanely fast. At tensions where U2 was probably the most I could get it to go with one flick, after I added some Maru lube I got it to do a U5. Maybe it has something to do with the tracks on the edge and center pieces.

Edit: Video

The U5 is towards the end, and it kind of looks like a U', but if you look closely you can tell it was actually a U5.
 
Last edited by a moderator:
The hurts over my review...
I needed a place to put that, anyway. It's the thread about this cube (which happens to be my favorite, in case you can't tell) and I figured that there isn't a more worthy place. My post was basically a "yes, but..." post that answered your question within the first few lines and the rest is for the people who, like me, actually read through forums ato search for relevant information they need. I've gotten help from totally superficial and unnecessary comments. I do answer with lots of text, yes, but that's just me.

If you haven't modded your SS Aurora and you're sure you have it tensioned correctly, then despite the fact that it rarely ever pops (although it's more prone to it than Dayan Zhanchi or Moyu Weilong), torpedoes are impossible. The pieces don't com apart in halves; they come with caps...

The only way to add an anti pop mech is to change the structure of the design, which I know nothing about.

As for the above post, WTF
I'm pretty sure that even when I purposefully tensioned my Zhanchi to have only one ridge of the screw in the core itself, the most I could get was a U4 wihtout it popping and flying everywhere. U5 is impossible.
 
The hurts over my review...
I needed a place to put that, anyway. It's the thread about this cube (which happens to be my favorite, in case you can't tell) and I figured that there isn't a more worthy place. My post was basically a "yes, but..." post that answered your question within the first few lines and the rest is for the people who, like me, actually read through forums ato search for relevant information they need. I've gotten help from totally superficial and unnecessary comments. I do answer with lots of text, yes, but that's just me.

If you haven't modded your SS Aurora and you're sure you have it tensioned correctly, then despite the fact that it rarely ever pops (although it's more prone to it than Dayan Zhanchi or Moyu Weilong), torpedoes are impossible. The pieces don't com apart in halves; they come with caps...

The only way to add an anti pop mech is to change the structure of the design, which I know nothing about.

As for the above post, WTF
I'm pretty sure that even when I purposefully tensioned my Zhanchi to have only one ridge of the screw in the core itself, the most I could get was a U4 wihtout it popping and flying everywhere. U5 is impossible.

I can get a u5, it just needs to be pretty loose.
 
I "planned" to make the aurora my main cube, but the quite large amount of corner twists I got turned me off. Maybe that's just me sucking at turning or having the tensions too loose, but twisting a corner on this cube doesn't take much effort and it happened alot while solving :(
 
I simply adapted my style to reduce twists and found that my turning became more accurate and that I cuased accidental pops a lot less. This is a really good intermediate cube capable of making sub-10 times, but good for those who aren't quite sub-20 yet (I'm currently 18-22 seconds average)
 
I really like this cube. It is very quiet and smooth. It also does not seem to catch at all and it is very good at slices. It is not the fastest, but it's smoothness makes up for that in my opinion. This may be my new Main very soon.
 
Back
Top