3D Printing?

SnappleXXL

Regular
Joined
Apr 30, 2009
Messages
46
Location
England
YouTube
Visit Channel
I know that 3d printing means printing something like puzzles or 3d objects, but how is this achieved and where can I print in 3d. Sorry if its a noobish question but I was just wondering, thanks.
 
3D printing technically refers to using inkjet-like technology to build three dimensional objects. There are many other technologies that can create 3D objects, but technically those technologies are 'rapid prototyping'. 3D printing is often used to refer to both of these technologies.

First off, 3D printing is still very, very expensive. To print something about the same size as a rubik's cube you can expect to pay around $400. And that would be on the cheap side. There are projects out there developing open-source 3D printers that are much cheaper (the printer itself would cost $500 to $2000 depending on your model, and also the material costs would be much lower) but they come nowhere close to the quality of commercial machines.

Most printers work by slicing the model into wafer thin layers (typically 0.3-0.03mm). By stacking these layers on top of each other, they build the model.

There are two inkjet based (real 3D printing) technologies out there, Polyjet and the technology used by ZCorp. Polyjet uses a printhead to deposit a UV curable resin. This technology achieves the best resolution with their layer thickness being the thinnest I mentioned. It has a price tag to match. ZCorp uses a HP printhead to deposit binder on a thin layer of plaster composite. Despite their layers being 0.1mm, the parts have a rather rough texture and are very fragile. This is the only technology that can print multiple colors in a single part but it is extremely unsuitable for puzzles.

For puzzles, the technology most employed is called FDM, fused deposition modeling. It is essentially a glue gun on steroids. A filament of plastic (ABS = most common plastic for cubes) is heated to it's melting point and is then forced trough a very small nozzle. The nozzle can move in two directions over the build platform to build 2D cross sections. After each cross section is built, the platform lowers by a little and the next layer is built. Overhanging parts are supported by a soluble plastic which can be removed using a alkaline solution. This technology is most suitable for puzzles but is very expensive. The cheapest printer in this range costs $15000, but as with all commercial printers (2D and 3D) the build material is extremely overpriced. The build platforms worth $.50 cost $12 each, and the build material has a similar price tag ($0.27/ml, which would make a Rubik's Cube cost $50 in plastic alone).

Another technology is called SLS, selective laser sintering. It is much like ZCorp building the object out of powder, but instead of glue a laser sinters (=melts) the powder together. Nylon is the most common build material but as with ZCorp the parts are not suitable for most puzzles.

SLA also uses a laser but instead of sintering powder, the laser is used to cure a resin. I don't know about it's suitability for puzzles (nobody has tried it as far as I know) but this technology is one of the oldest out there.

LOM, laminated object manufacturing uses either paper or plastic sheet. It uses a knife to slice the cross section out of paper or plastic and then glues it to the previous layers. Once the build is complete you have to remove the waste paper/plastic and you have your part. My guess is this isn't suitable for puzzles (especially the paper one) but nobody has tried it.

EBM, which is a lot like SLS uses an 'electron beam' to sinter layers of metal alloy together. If for some reason you ever wanted a titanium cube this would be the way to go, but this could be very, very expensive.

Finally, contour crafting in development at MIT will probably not be used to make puzzles, but houses. Not very useful in our context but certainly interesting. It is kind of similar to FDM, as it deposits fast drying concrete in a layer by layer style to from walls.

There are two open source 3D printers out there. Fab at Home uses two syringes to deposit whatever material you want, and RepRap is much like FDM. Unfortunately despite being pretty cheap neither is at a stage that they could produce cubes. For example, FDM currently still is five times more accurate than RepRap.

Usually someone designs the puzzle parts in a 3D version of paint. Then a few of each piece is printed and molds are made from those parts. A thermoset plastic is then poured into the mold to form the pieces inexpensively. Sometimes complete puzzles are made this way but moldmaking and casting from 'master parts' is more common.

This post turned out a bit longer than I wanted but I hope you enjoyed the read - it certainly took me a while to write as I haven't copied any text in here. For more information you should visit www.twistypuzzles.com/forum as the people over there are much more knowledgeable than the people here. We are also much more oriented to building puzzles rather than speedsolving them.
 
Back
Top