Lube?

ArcticxWolf

Regular
Joined
Sep 15, 2008
Messages
148
WCA ID
2010SINN01
YouTube
Visit Channel
Hi, I'm a new cuber and I'm wondering where I can get a decent lube for my rubiks cube. Also, I'm not really sure which brand to buy. I was using vaseline with my old rubiks brand one, but after a while, the cube didn't run smoothly, but rather, began to jerk instead.

By "a new cuber", I mean that I've been cubing since april, and my average time using the beginner method is 1:08:74. Recently (As of 3 days ago), I learned how to do the Fridrich method, and so far, my best time was 2:47:19.

I just got a new cube a few hours ago, and I don't want to mess it up like my old one. Help anybody?

Thanks
~ArcticxWolf
 
Go to walmart and look in the automotive section for HEAVY DUTY SILICONE by the "CRC" brand. I've never seen silicone that wasn't heavy duty, but i'm sure that would also work/ [if your not 18, bring a parent or they wont sell it to you]

PS, never use petroleum based lubricants like WD-40
 
i know this is now related but how often do you practice. i started slightly later than you yet i can easily average sub 20 and and some times sub 15
 
Your sig is a lie.
Seriously, you keep changing stories on of how good you are. How is that ecven relevant?
Oh yeah, and using jig-a-loo can be a bad idea. Just stick to a regular silicon lubricant.
 
Where do you live? In the US you can get CRC or Prestone silicone lubricant at most hardware/automotive stores. SNAP is a good brand too but I think it was recently discontinued. I don't know much about brands outside the US.

Just make sure you get a silicon based lubricant, NOT a petroleum based lubricant like WD-40. Check the labels.

Acetone isn't that bad as long as your cube isn't swimming in it. CRC contains acetone, but as long as you apply sparingly and let it dry properly your cube will be fine.
 
Acetone isn't that bad as long as your cube isn't swimming in it. CRC contains acetone, but as long as you apply sparingly and let it dry properly your cube will be fine.

Cubes are made of ABS

http://en.wikipedia.org/wiki/Acrylonitrile_butadiene_styrene
wikipedia said:
ABS polymers are resistant to aqueous acids, alkalis, concentrated hydrochloric and phosphoric acids, alcohols and animal, vegetable and mineral oils, but they are swollen by glacial acetic acid, carbon tetrachloride and aromatic hydrocarbons and are attacked by concentrated sulfuric and nitric acids. They are soluble in esters, ketones and ethylene dichloride.

The aging characteristics of the polymers are largely influenced by the polybutadiene content, and it is normal to include antioxidants in the composition. On the other hand, while the cost of producing ABS is roughly twice the cost of producing polystyrene, ABS is considered superior for its hardness, gloss, toughness, and electrical insulation properties. However, it will be degraded (dissolve) [5] when exposed to acetone. ABS is flammable when it is exposed to high temperatures, such as a wood fire. It will "boil", then burst spectacularly into intense, hot flames.
 
Yes, acetone dissolves plastic. But the acetone in silicone sprays like CRC is only a small amount and evaporates quickly. You're just applying a few spritzes; it's not like you're dunking your cube in a beaker of acetone.
 
Yes, acetone dissolves plastic. But the acetone in silicone sprays like CRC is only a small amount and evaporates quickly. You're just applying a few spritzes; it's not like you're dunking your cube in a beaker of acetone.

That is true. My cubes are still fine after CRC. But I don't lube much or put a lot in it.
 
Cubes are made of ABS

http://en.wikipedia.org/wiki/Acrylonitrile_butadiene_styrene
wikipedia said:
ABS polymers ...However, it will be degraded (dissolve) [5] when exposed to acetone. ABS is flammable when it is exposed to high temperatures, such as a wood fire. It will "boil", then burst spectacularly into intense, hot flames.

now i know what to do with my extremely broke rubiks 5x5.:D

LOL

Please provide a video! And be careful!
 
Back
Top