V-Cube 4

Another tip.. on assembling the center pieces.. put the centerpiece that goes on the notch on first :)

@MaeLSTRoM: did you remove the flash as well? I am removing the flash right off the bat now while assembling.



Making pics as I go folks :) They will come up in a while.

Looks like somewhere between 62 and 63mm in size.


Single inner slices without issues!!
Double inner slices ditto! :D
 
Last edited:
I'll quickly make one before the light gives out here. Please forgive the stupidity as I am NOT used to solving a 4x4 at all. LOL Will be corner cutting and slicing and such only.


Cube weight is 150grams exactly. Uploading my little vid now :)


Shoot I forgot something...

dinner..

ROFL!!!!
 
Last edited:
At this point it is better than the SSv5, as there IS no SSv5 yet. ;) LOL

But on the slicing.. if you are a slicer, this cube is perfect. Just did some slices on one inner layer till the middle finger when ughhhh hehe.. didn't lock.
Slices on both inners are smoother than on the single.

Turning layers.. outer layers are smoother turning than two layers at once.

Do note that I have yet to tension the cube proper and as I have NO experience on speedsolving the 4x4 (which should change I am sure ;) ) it is best to view speedcubers' reviews of course on that.

Vid will be live in about 30-35 minutes, right here: http://youtu.be/h0Kuq_cUwbw
Forgive the quality in advance hehe ;)

I will embed it once I see that it goes live.
 
Last edited:
Well then I hope it will be a pre-modded one so to speak.. to solve the inner layer slice lockups.

Working on the pictures of the assembly now :)

Oh.. *goes get something to eat* stupid me.. three HOURS past dinner time and I finish assembling this cube and tummy NOW decides to go GRRRRR lol

(and then to know that I have a 3x3x4 DIY kit here as well .. but uhhh.. tomorrow!!)



Ah there we go:
 
Last edited by a moderator:
Well then I hope it will be a pre-modded one so to speak.. to solve the inner layer slice lockups.

Working on the pictures of the assembly now :)

Oh.. *goes get something to eat* stupid me.. three HOURS past dinner time and I finish assembling this cube and tummy NOW decides to go GRRRRR lol

(and then to know that I have a 3x3x4 DIY kit here as well .. but uhhh.. tomorrow!!)



Ah there we go:

That's promising , slices are very smooth , which is perfect for me to use in 4BLD :D a little disappointed about corner cutting in the centers , but I guess tensioning and lubing will improve it a lot , very very promising , thank you a lot =)
 
Last edited by a moderator:
You're welcome!!

If you happen to know a good tensioning tutorial for the 4x4, I'm game. On one end it is like it feels too lose, on the other end it feels like it could loosen up. All tensions are equal around the cube, but.. I just basically have no clue how to tension it proper you know..

Working on the pics now.. will upload and put those in as well. :)
 
Looks pretty good, reverse cutting doesn't seem great but forward cutting is nice, but I just finished modding my SS IV and it's good (I can even slice), so I probably won't get it.

I'm interested to see speedsolves to see how it performs - probably similar to pillowed I know, but it might be easier to handle because it's flat.
 
Here are the assembly pictures:


All sides assembled
01centersin.jpg


First half arch (use tape.. really.. lol)
02twoarches.jpg


Another quarter arch
03thirdarch.jpg


First two whole arches all done
04fourarches.jpg


Inserting the center and edge pieces of the first layer
05firstcenteredge.jpg


Inserting the corner
06fullcubecorner.jpg


Second layer centers and edge
07secondlayer.jpg


And the arch pieces added to lock things in place
08secondlayertop.jpg


Then the upper arches are built, corners inserted first
09archescorners.jpg


Sticking the centers and edges in the available smaller space
10srdlayercenteredge.jpg


Centerpieces first
11startinglastlayer.jpg


Last bits and pieces
12lastcenters.jpg


And the final bits, the edges
13edgesonly.jpg
 
Thank you!! Looking forward to a speedcuber's opinion on this one!




Just changed the springs around from hard to the medium ones again. One of the centerpieces was grinding its screw against the pieces so I changed that to the medium and immediately felt the difference and cube turned much smoother, so.. changed them all :)
 
Last edited:
Thank you!! Looking forward to a speedcuber's opinion on this one!




Just changed the springs around from hard to the medium ones again. One of the centerpieces was grinding its screw against the pieces so I changed that to the medium and immediately felt the difference and cube turned much smoother, so.. changed them all :)

does the assembled version come with medium , soft or hard springs :) ?
 
I have no clue. Might want to mail verdes on that one :) I'd say go for a DIY, OR try and get two more sets of springs along with the ready made one.. the prices are the same, so.. in theory.. yadda yadda no prob etc. In theory :)
 
Back
Top