Dayan 6: PanShi [pictures]

I just assembled and properly lubed my white panshi. I've tried different tensions.

My impressions are: Its very bumpy, i can feel huge bumps in it, and if I scramble it and put it on the table, the cube is not a nice square, its just a mess..
It locks up a lot, its not fast, its not smooth

I know you really shouldnt judge a cube until its broken in. But honestly, it feels like pure crap :-(

Maybe it will get nice onces its broken in, but right now, I cant see how its and improvement of any Dayan cube.
 
Last edited:
I'm pretty sure the bumpiness is the corner piece catching on the center I mentioned earlier. It's to such a degree that I don't think your typical "breaking in" will make a significant difference. In my opinion, ZanChi > LingYun > GuHong > LunHui >>>> PanShi. I'm waiting to hear what everyone else's opinion is.
 
I just tried taking them out, and lubed all the contacts points that are different from regular Dayans. Tensioned it until the point where it doesn't pop. Its better, for sure. But i still find it a bad cube compared to zhanchi and guhong...

Really not impressed. But as i said. Breaking in can do a loooot difference, so I wont give up :)
 
In my opinion zhanchi 55mm with stickerless center pieces is the perfect cube. Fast as a Zanchi, smooth as a guhong :)
But ill be using the Panchi for a while, too see what it can do.

In my opinion a brand new zhanchi is worthless, but after a few hundred solves its pretty nice.

Right now my Panchi feels slow as a Guhong, but without the smooth feeling.
 
Oh is that a common problem? I got a broken corner piece. Doesn't seem to have any affect tho but ill be getting a new piece :)
 
Lol these negative reviews are scaring me off and are making me think that I would've been better off just buying a new ZhanChi.

The reason I bought a PanShi is not because I wanted to try it but because my stickerless ZhanChi is covered in ink stains and I can't get them off anymore (and stuff that gets it off eats away the plastic). If it wasn't for that, I'd still be using the ZhanChi because that has been my favorite cube of all time up until now.

I decided to buy a new cube to replace the ink-stained one and saw there was a new one (the PanShi) and figured I might as well buy that one because it's Dayan right? My experience with Dayan is that each successor is always better than its predecessor. But now that I'm reading the reviews, I'm not so sure anymore lol.

Ah well, I bought it at Lubix which means it'll be modded and tensioned and everything so it might still turn out great. I haven't lost all of my hope yet. :p I'll keep you guys posted on my experience with the PanShi when it arrives.
 
I received mine assembled this afternoon from Puzzle Addictions.
It's clunky. There are certainly point where parts of pieces are coming into direct contact with others.
However, after simply tensioning the cube, it turns very well. While I'm not a very accurate turner, I don't require much corner-cutting ability, so the only thing that's stopping this cube from being great is this clunkiness.
Even so, it's still a nice cube. I'll definitely use it. It's worth using.

But if you're going for a cube that's nice out of the box, 55mm ZhanChi has served me well.
 
However, after simply tensioning the cube, it turns very well. While I'm not a very accurate turner, I don't require much corner-cutting ability, so the only thing that's stopping this cube from being great is this clunkiness.
Even so, it's still a nice cube. I'll definitely use it. It's worth using.

I'm guessing you've tensioned it pretty tight? I did notice that either loose or tight tensions did help with the catching issue, but it was either too loose or lost most of it's corner cutting ability. I'll try tighter tensions again and see how that works out.
 
I'm guessing you've tensioned it pretty tight? I did notice that either loose or tight tensions did help with the catching issue, but it was either too loose or lost most of it's corner cutting ability. I'll try tighter tensions again and see how that works out.

I loosened it. Mine cuts line to line (37ish degrees? I believe Stefan had a picture with the actual alignment angle). At fast speeds, it feels a bit crisp, reminiscent to an A-II.
 
Everyone has their own opinion, and that's his. Well, I'd say that the Panshi would be one of the cubes with the most flow if it weren't for the bumpy feeling. It reverses very easily, easier than the zhanchi, in my opinion. Although it doesn't reverse much, it does small amounts with ease.

Those that have gotten their Panshi orders from Puzzleaddictions, are the stickers that you guys got fitted? My friend's stickers aren't fitted, but on some unboxings on youtube, the stickers are.
 
I have no opinion on this cube. I was going to do a youtube video, being one of the first people to have recieved the mass produced version, but I couldn't think of anything to say. Its been a week, and I can't even sub 25 with it. At first, I thought it was because of the tensions, so i tensioned it looser, and it just locks up like crazy. I then thought it was because of my lube (i use maru) so I ordered lubix from icubemart, and tried lubing it with that. To make a long story short, this is a really big disappointment... I hope dayan thinks of an even better design to top the zhanchi. Which is kinda sad, cos i ordered it from the first store up (on taobao), which actually amounts in 2 55mm zhanchis...

If you want it for speedcubing, stick with zhanchis. If you want it as a collector's item, get it. I hope some1 thinks of a good mod for it soon... looking forward to the fangshi :P
 
Ive looked into the cube and the problem I see is that the corner pieces gets caught on the center pieces. I think the idea is that the corner piece is supposted to "slide of" the center piece, to make it smooth even if you dont turn it perfectly. Therefore it reverse cuts very easily. But these cubes aren't perfectly made. I think its a good idea, but it didnt turn out quite as they though...I think a minor adjustment to the center pieces might help. Im gonna give it a go and get back to you

Im guessing the cube will get much better with some breaking in, but im not that patient ;-)

Actually looking into this cube a bit more I think its a lost cause. Im just gonna put it on the shelf and stick with my zhanchi55
 
Last edited by a moderator:
I assembled mine yesterday. I did not use torpedoes.
I put a drop of clue on my corners, and tied it off with string to dry. Got all my corners done in a few minutes this way.
Corner.jpg
This is probably my best cube, I have gotten a few pops per ao100 which is normal.

I'm glad someone is reiterating what I've been saying for a couple days now, re: the center-corner catching.
I have no catching whatsoever. : |
 

Attachments

  • IMG_0519.jpg
    IMG_0519.jpg
    480.7 KB · Views: 59
Back
Top