Sanding for corner cutting

Status
Not open for further replies.

Sm1thson

Member
Joined
Jul 30, 2008
Messages
6
Right I started with a £1 cube (no springs), it was nightmare, so stiff and constantly locked up. After some serious dremeling and silicone lubing it was half decent but when it locks up it locks up hard (and it pops more now).

My wife has now bought me a transparent DIY I built it and fiddled with it till it got stiff (from the dust inside building up) to wear it in, I then washed it lubed it and rebuilt it. It works very nice, but compared to my friends ‘speedcube’ (white type A I think) the area mine still lacks in is cutting corners. My idea is to sand the edges on the 6 centre pieces to round them off more I did this on my first cube and It seamed to help but I cant be sure as I made a lot of modifications to it at the time.

Has anybody else tried rounding off the centre pieces? (or fancy trying it and reporting back?) I wasn’t going to sand (/dremel) this cube so if I do I want to make sure I do it right!
 
Unless I'm very much mistaken, the corner-cutting ability of a cube comes from the "roundedness" of the interiors and has little to do with the centre pieces. In other words, if the interior of your cube (assembled) looks like a sphere, it's gonna cut corners well; if it looks likes some weird polyhedron, it's not.

Why don't you just spend some money on cube4you DIYs, rather than time and energy on sanding your cube, which may very well culminate in a completely destroyed and unusable cube? That mentioned, you can do all you want to your crappy cube once you get a DIY ;)

Besides, don't spend so much time and effort on a transparent cube which can't be used in WCA competitions anyway. Put your effort into improving a cube that's worth the improvement.
 
Last edited:
Unless I'm very much mistaken, the corner-cutting ability of a cube comes from the "roundedness" of the interiors and has little to do with the centre pieces. In other words, if the interior of your cube (assembled) looks like a sphere, it's gonna cut corners well; if it looks likes some weird polyhedron, it's not..
cool Ive searched a lot before for the best place to sand, but its always been inconclusive. When it snags/ locks it does look like it’s the corner cubes that snag on the centre ones tho. Any other opinions/ links where this has been bottomed out.

Why don't you just spend some money on cube4you DIYs, rather than time and energy on sanding your cube, which may very well culminate in a completely destroyed and unusable cube? That mentioned, you can do all you want to your crappy cube once you get a DIY ;)
I have 2 cubes, a £1 one which I have spent time on (I enjoy fiddling) and a transparent cube that my wife got me which is a cube4you DIY, it is very good by all accounts I just feel it could be a little bit better.

Besides, don't spend so much time and effort on a transparent cube which can't be used in WCA competitions anyway. Put your effort into improving a cube that's worth the improvement.
I’m not planning on going anywhere near any competitions (I cant even solve it yet lol), transparent was my favorite of the DIY’s, I had read speculations that it wasn’t quite as good but knew it would be good enough for me, which it is. I just like to fiddle and if it can be improved easily then why not!
 
I was about to edit my previous post in case you found it offensive (because of something else that happened in another thread) but seems you're okay with it, so I'll leave it as it is.

Have fun fiddling with your cube then :)
 
lol, there was nothing for me to be offended at in there! (and taking offence over the interwebnet is daft)

another thing I have read is adding the Type A core + springs etc improves it so i might try that before sanding, unless someone convinces me to sand (come on its clear i want to sand it, I just dont want to kill it lol.).
 
Rounded cube pieces won't help you cut corners much. If you look at the Type F DIY cube on Cube4you, the pieces are very rounded. But... it doesn't cut corners well. Why? Because the Type F core stinks. The corner cutting usually has to do with the core.

My store bought cube turns AMAZINGLY but it stinks at cutting corners. I replaced the core with a Type A core and it's an AWESOME cube. Turns and cuts corners great! :)
 
Dude no one said anything about "external roundedness". No one cares how rounded a cube looks on the outside. All we suggested was "rounding" the internal part of the cube. And it is the internal roundedness that determines whether or not a cube cuts corners well.

I might wanna try what Theron Rabe suggested though, seems like a good idea ;)
 
Dude no one said anything about "external roundedness". No one cares how rounded a cube looks on the outside. All we suggested was "rounding" the internal part of the cube. And it is the internal roundedness that determines whether or not a cube cuts corners well.

I might wanna try what Theron Rabe suggested though, seems like a good idea ;)

All you need to do is look carefully where the cube jams. It's where the inside corners of pieces catch the inside edges of pieces. By "corners" I do not mean corner pieces, but the spot there 3 surfaces meet on a piece. By "edges" I mean the places where 2 surfaces meet on a piece. For example, the jam can occur where a corner of a center piece catches the edge of a corner piece.

I bought a metal file to scrape down the interior edges and corners of pieces to prevent jams, but I have not done it yet. I think you might want to be careful of rounding the edges and corners of the center pieces to an extreme, because then the centers might unintentionally turn 90 degrees while cubing.
 
All you need to do is look carefully where the cube jams. It's where the inside corners of pieces catch the inside edges of pieces. By "corners" I do not mean corner pieces, but the spot there 3 surfaces meet on a piece. By "edges" I mean the places where 2 surfaces meet on a piece. For example, the jam can occur where a corner of a center piece catches the edge of a corner piece.

I bought a metal file to scrape down the interior edges and corners of pieces to prevent jams, but I have not done it yet. I think you might want to be careful of rounding the edges and corners of the center pieces to an extreme, because then the centers might unintentionally turn 90 degrees while cubing.

I never intended to sand any part you mentioned off my centers. Clarification: "interior" means interior interior, like really interior, you know, the part of the cube that you can see only when you pop a piece out, the "edges of centers" is not considered the interior of the cube and I doubt sanding that'll contribute to the corner-cutting ability of the cube.

And whatever jams you mentioned is easily eliminated by breaking into your cube, really, very easily if you cube as frequently as I do. I wouldn't risk destroying my cube by over-sanding it, I'd just cube for hours and the surfaces will smooth themselves out over time, but that's just me :p
 
Rounded cube pieces won't help you cut corners much. If you look at the Type F DIY cube on Cube4you, the pieces are very rounded. But... it doesn't cut corners well. Why? Because the Type F core stinks. The corner cutting usually has to do with the core.

My store bought cube turns AMAZINGLY but it stinks at cutting corners. I replaced the core with a Type A core and it's an AWESOME cube. Turns and cuts corners great! :)

yeah i think an A core +springs etc + lots of playing with it is going to be the best thing. I'll put the dremel away.

I think the new springs will equally help, from what I can remember the springs in my friends cube (type A i think) seem to be not as strong so you can tighten the cube more (less popping) and it will rotate more free (less jamming).
 
Status
Not open for further replies.
Back
Top