QJ Pyraminx corner caps.

How do you, or did you, take off the corner caps?

It's quite tricky, but I was able to take mine off after a few minutes.

Turn the tip/corner 60 degrees or whatever angle it would be on a pyraminx, and get a flat head screwdriver, and put it in under one of the sharp vertices (not the "line" part of the tip, the sharp point where two "lines" meet) and with some force it'll fly off. If you can't get your screwdriver under one of the vertices, try a different one.

- Saber

EDIT: We all have Pokemon icons! :D
 
I'm pretty sure the twisty things on the ends are the corners lol
tips...

No difference.

I don't like wikipedia's definition of a corner:

A corner is the place where two lines of different dimensions meet at an angle,

I'd say:

A corner is the place where two lines of different dimensions meet at a right angle

For a tip, i'd say

A tip is the place where two lines of different dimensions meet at an angle θ =/= 90
 
I'm pretty sure the twisty things on the ends are the corners lol
tips...

No difference.

I don't like wikipedia's definition of a corner:

A corner is the place where two lines of different dimensions meet at an angle,

I'd say:

A corner is the place where two lines of different dimensions meet at a right angle

For a tip, i'd say

A tip is the place where two lines of different dimensions meet at an angle θ =/= 90

So would you say that a megaminx doesn't have corners? Defining a corner as a place where two lines of different dimensions meet at an angle is a pretty standard and in no way unique to wikipedia.
 
I'm pretty sure the twisty things on the ends are the corners lol
tips...

No difference.

I don't like wikipedia's definition of a corner:

A corner is the place where two lines of different dimensions meet at an angle,

I'd say:

A corner is the place where two lines of different dimensions meet at a right angle

For a tip, i'd say

A tip is the place where two lines of different dimensions meet at an angle θ =/= 90

So would you say that a megaminx doesn't have corners? Defining a corner as a place where two lines of different dimensions meet at an angle is a pretty standard and in no way unique to wikipedia.

Using my definition, no, the megaminx does not have corners, it has tips. I'm being extremely pedantic. Perhaps a corner is defined as when two lines of different dimensions meet at an angle >60, whatever, it's an interesting topic.
 
How do you, or did you, take off the corner caps?

It's quite tricky, but I was able to take mine off after a few minutes.

Turn the tip/corner 60 degrees or whatever angle it would be on a pyraminx, and get a flat head screwdriver, and put it in under one of the sharp vertices (not the "line" part of the tip, the sharp point where two "lines" meet) and with some force it'll fly off. If you can't get your screwdriver under one of the vertices, try a different one.

- Saber

EDIT: We all have Pokemon icons! :D
I still can't get them off. the glue must be really strong or something.
I'm using so much force that, I'm scraping off the plastic. do I need a small flat head? or a big one?
 
I actually do it differently. I turn it 60 degrees and stick a knife beneath one of the sides of the tip, not one of the vertices. That way I can pry it off. Depending how much glue is on it, you may have to do this to all three sides. If there's too much glue, it may ruin the core if you happen to pull the entire screw out, but it should be fine with a QJ pyraminx. This probably won't work with screwdrivers since they're too thick, so if using a knife is too dangerous, this probably isn't going to help.

Using my definition, no, the megaminx does not have corners, it has tips. I'm being extremely pedantic. Perhaps a corner is defined as when two lines of different dimensions meet at an angle >60, whatever, it's an interesting topic.
Well I could define a circle as a curved line where both ends meet, but that's not necessarily what a circle is, is it?
http://dictionary.reference.com/browse/corner
 
Last edited:
I actually do it differently. I turn it 60 degrees and stick a knife beneath one of the sides of the tip, not one of the vertices. That way I can pry it off. Depending how much glue is on it, you may have to do this to all three sides. If there's too much glue, it may ruin the core if you happen to pull the entire screw out, but it should be fine with a QJ pyraminx. This probably won't work with screwdrivers since they're too thick, so if using a knife is too dangerous, this probably isn't going to help.

Using my definition, no, the megaminx does not have corners, it has tips. I'm being extremely pedantic. Perhaps a corner is defined as when two lines of different dimensions meet at an angle >60, whatever, it's an interesting topic.
Well I could define a circle as a curved line where both ends meet, but that's not necessarily what a circle is, is it?
http://dictionary.reference.com/browse/corner

could you make a video? I don't really get how you do it.
 
I actually do it differently. I turn it 60 degrees and stick a knife beneath one of the sides of the tip, not one of the vertices. That way I can pry it off. Depending how much glue is on it, you may have to do this to all three sides. If there's too much glue, it may ruin the core if you happen to pull the entire screw out, but it should be fine with a QJ pyraminx. This probably won't work with screwdrivers since they're too thick, so if using a knife is too dangerous, this probably isn't going to help.

Using my definition, no, the megaminx does not have corners, it has tips. I'm being extremely pedantic. Perhaps a corner is defined as when two lines of different dimensions meet at an angle >60, whatever, it's an interesting topic.
Well I could define a circle as a curved line where both ends meet, but that's not necessarily what a circle is, is it?
http://dictionary.reference.com/browse/corner

A circle is absolutely defined. It appears a corner and a tip are ill-defined. Why do you think there's a topic being debated here?
 
could you make a video? I don't really get how you do it.
Sorry, I find it too trivial to make a video. I'll go through step-by-step though...

1) Place pyraminx on table and rotate until the edge of the pyraminx is facing you.
2) Rotate the tip on the top 60 degrees so that the flat side of the tip is facing you.
3) Wedge knife underneath tip enough that you can pry the cap off. Make sure you don't stick it in too far, otherwise it will just catch on the piece that is holding the cap in place.
4) Repeat on all three sides of the tip until the cap comes off.

I actually do it differently. I turn it 60 degrees and stick a knife beneath one of the sides of the tip, not one of the vertices. That way I can pry it off. Depending how much glue is on it, you may have to do this to all three sides. If there's too much glue, it may ruin the core if you happen to pull the entire screw out, but it should be fine with a QJ pyraminx. This probably won't work with screwdrivers since they're too thick, so if using a knife is too dangerous, this probably isn't going to help.

Using my definition, no, the megaminx does not have corners, it has tips. I'm being extremely pedantic. Perhaps a corner is defined as when two lines of different dimensions meet at an angle >60, whatever, it's an interesting topic.
Well I could define a circle as a curved line where both ends meet, but that's not necessarily what a circle is, is it?
http://dictionary.reference.com/browse/corner

A circle is absolutely defined. It appears a corner and a tip are ill-defined. Why do you think there's a topic being debated here?
So are you saying that a corner isn't absolutely defined? Just because several people don't know exactly what a corner is doesn't mean the word itself isn't properly defined. I would call that confusion, not a debate. A debate is held over something that does not have a clear answer, and the definition of "corner" is something you can't change.
 
could you make a video? I don't really get how you do it.
Sorry, I find it too trivial to make a video. I'll go through step-by-step though...

1) Place pyraminx on table and rotate until the edge of the pyraminx is facing you.
2) Rotate the tip on the top 60 degrees so that the flat side of the tip is facing you.
3) Wedge knife underneath tip enough that you can pry the cap off. Make sure you don't stick it in too far, otherwise it will just catch on the piece that is holding the cap in place.
4) Repeat on all three sides of the tip until the cap comes off.

I actually do it differently. I turn it 60 degrees and stick a knife beneath one of the sides of the tip, not one of the vertices. That way I can pry it off. Depending how much glue is on it, you may have to do this to all three sides. If there's too much glue, it may ruin the core if you happen to pull the entire screw out, but it should be fine with a QJ pyraminx. This probably won't work with screwdrivers since they're too thick, so if using a knife is too dangerous, this probably isn't going to help.

Using my definition, no, the megaminx does not have corners, it has tips. I'm being extremely pedantic. Perhaps a corner is defined as when two lines of different dimensions meet at an angle >60, whatever, it's an interesting topic.
Well I could define a circle as a curved line where both ends meet, but that's not necessarily what a circle is, is it?
http://dictionary.reference.com/browse/corner

A circle is absolutely defined. It appears a corner and a tip are ill-defined. Why do you think there's a topic being debated here?
So are you saying that a corner isn't absolutely defined? Just because several people don't know exactly what a corner is doesn't mean the word itself isn't properly defined. I would call that confusion, not a debate. A debate is held over something that does not have a clear answer, and the definition of "corner" is something you can't change.

sorry, I still don't get it. so the pyraminx is facing me like:
1 1

1 ?
or:
2

2 2 ?
and when I stick the knife under, I stick it this way right?
1

1 1
^ (in the middle)
 
sorry, I still don't get it. so the pyraminx is facing me like:
1 1

1 ?
or:
2

2 2 ?
and when I stick the knife under, I stick it this way right?
1

1 1
^ (in the middle)

In your last diagram, what I do is I stick the knife in parallel to the tip. That way when you try to pry it off, it's going to pull the entire edge up, not just a single point underneath the cap.
 
Back
Top