Dapianokid
Regular
- Joined
- Aug 24, 2013
- Messages
- 214
rj, if it pops, then you're doing it wrong or it isn't tensioned well enough. This cube performs well at loose and tight tensions, but it tends to pop at looser tensions. At tighter tensions, out of 1000 solves, I only got 2 pops, and I'm a rough turner. So torpedoes are not needed if you tension it right... There is a little hole there in the edge pieces for some reason, and I thought maybe it was for torpedoes, but apparently not. Besides, gluing pieces on the internal mechanism is a bad idea, it messes with the symmetry of the design.
All in all, I find this to be an amazing cube. It's a good step up from your basic "entry level" speedcube, bridging the gap between slow cubes and cubes like the Moyu Weilong and the Dayan Zhanchi. Definitely a good main speedcube, especially for those averaging between 20 and 40 seconds. I don't know about faster times, but I can attest to perfect performance in that range. Etiher way, I still prefer faster cubes, even if this one is an amazing cube.
It has a veryyy smooth feel. Like creamy butter. It's gorgeous, I think. The pieces can stretch very far even on the tightest tension, looking like it should just fall apart. It's extremely controllable. The tracks are good, but causes lubing to be a problem, as it actually tends to increase friction. So I lube it VERY sparaingly.
It's made of cheap plastic and comes with amazing stickers. The plastic is bad enough that when somebody once dropped it on concrete (he's never touching my cubes again.), it had a dent/abrasion mark. I would get a black one, in that case. Though it is beautiful in either color. The stickers it comes with are just superb and slightly brighter than you'd expect from other ShengShou cubes.
The corner cutting is phenominal and can be good at multiple tensions. Reverse corner cutting varies from core to core, and from face/side to face/side. It's not absolute and you might not get the same results as I did. My white SS Aurora's green side can corner cut about 55 degrees and reverse corner cut nearly an entire cubie, or about 37.5 degrees. The white side, however, can only corner cut 44 and reverse cut about half a cubie with a fair amount of effort. Any further, and it simply locks. It'll pop if you try to unlock it. If it locks, trust it. It means it simpluy cannot do what you're asking of it. It doesn't need it, though. Cutting is completely effortless all the way up to 40 degrees. It feels a bit smaller than your average cube because of the embezzeled cubies and smoothened exterior. The mech is simple and effective, without added complications or features. It's easy to mod (48 PEM and 24 CPM should be applied by any serious cuber. makes this cube even smoother.) and fun to just solve! Slowly solving is so smooth it made me giggle for the first few DOZEN solves. It's hilariously nice to turn.
It's also dead silent unless you're going for insane TPS. It makes no noise whatsoever for the accurate turner.
Besides the above mentioned flaws and the fact that you can very easily twist the corners, even on tight tensions (but I've NEVER actually had a corner twist during a real, fast, agressive solve. I've solved it hundreds of times), his cube is a very high quality cube.
I recommend it for newbs and veterans alike. Good for efficient methods and the M slices on this baby flow like no other cube can attest to. It even corner cuts M slices.
Those are my thoughts on the SS Aurora, which was my main until I switched to the Moyu Weilong
All in all, I find this to be an amazing cube. It's a good step up from your basic "entry level" speedcube, bridging the gap between slow cubes and cubes like the Moyu Weilong and the Dayan Zhanchi. Definitely a good main speedcube, especially for those averaging between 20 and 40 seconds. I don't know about faster times, but I can attest to perfect performance in that range. Etiher way, I still prefer faster cubes, even if this one is an amazing cube.
It has a veryyy smooth feel. Like creamy butter. It's gorgeous, I think. The pieces can stretch very far even on the tightest tension, looking like it should just fall apart. It's extremely controllable. The tracks are good, but causes lubing to be a problem, as it actually tends to increase friction. So I lube it VERY sparaingly.
It's made of cheap plastic and comes with amazing stickers. The plastic is bad enough that when somebody once dropped it on concrete (he's never touching my cubes again.), it had a dent/abrasion mark. I would get a black one, in that case. Though it is beautiful in either color. The stickers it comes with are just superb and slightly brighter than you'd expect from other ShengShou cubes.
The corner cutting is phenominal and can be good at multiple tensions. Reverse corner cutting varies from core to core, and from face/side to face/side. It's not absolute and you might not get the same results as I did. My white SS Aurora's green side can corner cut about 55 degrees and reverse corner cut nearly an entire cubie, or about 37.5 degrees. The white side, however, can only corner cut 44 and reverse cut about half a cubie with a fair amount of effort. Any further, and it simply locks. It'll pop if you try to unlock it. If it locks, trust it. It means it simpluy cannot do what you're asking of it. It doesn't need it, though. Cutting is completely effortless all the way up to 40 degrees. It feels a bit smaller than your average cube because of the embezzeled cubies and smoothened exterior. The mech is simple and effective, without added complications or features. It's easy to mod (48 PEM and 24 CPM should be applied by any serious cuber. makes this cube even smoother.) and fun to just solve! Slowly solving is so smooth it made me giggle for the first few DOZEN solves. It's hilariously nice to turn.
It's also dead silent unless you're going for insane TPS. It makes no noise whatsoever for the accurate turner.
Besides the above mentioned flaws and the fact that you can very easily twist the corners, even on tight tensions (but I've NEVER actually had a corner twist during a real, fast, agressive solve. I've solved it hundreds of times), his cube is a very high quality cube.
I recommend it for newbs and veterans alike. Good for efficient methods and the M slices on this baby flow like no other cube can attest to. It even corner cuts M slices.
Those are my thoughts on the SS Aurora, which was my main until I switched to the Moyu Weilong