way to improve 4x4x4

GalPro

Regular
Joined
Dec 31, 2008
Messages
98
Hi,
I have an original 4x4,
but it's horrible, every twist it gets stuck, and you have to twist the same side a few times to get it working,

do you have a suggestion on what to do?

Thanks
 
You have the newer rubik's 4x4, which is generally the worst 4x4. Is this before or after you lubed it? Personally what I would do either way is just get an eastsheen. I made the same mistake you did when I first got a 4x4, I didn't research at all which cube to get because I just wanted any. I never touch my rubik's revenge anymore because it's terrible.
 
I have the same Rubiks 4x4x4 as you I think and I averaged 2:30 with it because it gets stuck every twist I do as it is the case with yours. Now I got an eastsheen and my average is now 2:25 - *g*. The problem is, that I'm a little bit color-weak (or how is it called?) and I cannot easily distinguish between the pink and the red.. don't forget to buy an extra orange sticker set for that problem if you buy an eastsheen which is strongly recomended =)
 
ya, i have a rubiks revenge from about a month ago

mine doesnt seem to lock up as much as others but try lubing it and make sure its broken in, that may help
 
I think I had a pretty bad Rubik's 4x4. While It was in bad condition, I didn't know how to solve it. The day I learned how to solve it, I lubricated it. Now it works really great. I took it all apart and laid out all the pieces, and spayed them with silicone spray. Then put it back together, and waited for it to dry. Then it worked really great. It tends to lock up sometimes, but works great compared to what it was.
 
I didn't lubericate my 4x4,
if I do, it will improve?

(btw - I used silicon grease for my 3x3 and it worked out pretty good)

and I don't really think that I would buy an eastsheen, because I'm planning to buy a vcube 5 in a month, (I wanna get 1 of each cube first lol)
 
I lubed mine. It got a little better, but not much.


I'd say it's my worst cube by a fair amount. It locks up for absolutely no reason and can be nearly impossible to unlock--I often have to go the long way around with an R3 instead of R' (or the equivalent on any face). My times are a good 15-20 seconds higher with it. It's really bad. Get an Eastsheen or a Meffert's.

EDIT: that said, the quality of a cube has only so much of an effect on your times. I wouldn't be at all surprised if one of the good 4x4x4 cubers was able to get impressive times out of a new rubik's.
 
Should I try and lubricate it too?

Because the cube is quite loose right now,

If it is already loose, then you are probably okay. Lube might help the pieces glide a bit better off each other, avoiding a lockup. If you lube it, I recommend carefully taking it apart and wiping the cube dust and grime off first. Two decades ago, I used to use Vaseline but it weakened the center piece stems and they snapped pretty easily. So, I recommend something without petroleum if possible. Something with silicone is probably best, although the "cube lube" from Rubik's or PuzzleProz should be safe.
 
I have a new Rubik's 4x4, and I love it! I did not lubricate it at all. Here's what I did. I had 2 rubik's 4x4's, and I took the pieces from both that had the least imperfections (there were a lot!). I used a VERY fin sandpaper, and sanded off the imperfections that caused lockups. If it did not cause a lockup, then I just left it (oversanding this cube will cause many pops). Now I clean all the cubies with water. I will dry it off a little bit, but I don't worry too much about about getting every last drop. I put it together, and I just broke it in using my hands. I NEVER lubricated it, and now it is amazing. You have to be careful with sanding, and I only recommend sanding it if there are a lot of imperfections.
 
I have a Rubik's Revenge and its a hundred times better than my eastsheen 4x4. Something I noticed about Rubik's brand cubes is that if you take them apart and put them back together, they loosen up even without lube. Try taking it apart and lubing each piece and let them dry and put it back together, it should help a bunch.
 
Back
Top